background image

5

2. Firmly grasp the power cord and pull to completely remove 

the power cord, cord restraint, and pin from the rear panel. 

3. Confirm that the power cord restraint (A), and pin (B) are 

removed.   

4. To remove the power cord from the cord restraint, push the 

power cord in, press TAB, and then pull the power cord out. 

Looped power cord

1. Firmly grasp the yellow shipping strap and pull until both ends 

are completely removed from washer. 

2. Check that two (2) cotter pins were removed with the shipping 

strap. 

Connect Drain Hose

Proper connection of the drain hose protects your floors from 
damage due to water leakage. Read and follow these instructions.
The drain hose is connected to your washer and is stored inside 
the washer cabinet.

Remove drain hose from washer cabinet

Gently pull the corrugated drain hose out of the washer from the 
top of the hose. Continue to pull the hose until the end emerges. 
Do not force excess drain hose back into the rear of the washer.

Laundry tub drain or standpipe drain 

Connecting the drain hose form to the corrugated 
drain hose   

1. Feed end of drain hose into one end of form. Place end of 

drain hose form into the drain hose relief. 

2. Bend the hose over the top of the form and feed into the other 

end of the form. 

A. Power cord restraint

B. Pin

Looped power cord

A

B

A. Drain hose reliefs

A

Summary of Contents for W10038090









Reviews: