background image

14

Sizing Between Single or 2

nd

 Stage Regulator and Appliance*

Maximum propane capacities listed are based on 

¹⁄₂

" W.C. pressure drop at 11" W.C. setting. Capacities in 1,000 Btu/h.

Data in accordance with NFPA pamphlet Number 54.

Start-up, Adjustments and Checks

Heating Start-up

This unit is equipped with an electronic ignition device to 
automatically light the main burners. It also has a power vent 
blower to exhaust combustion products.

On new installations, or if a major component has been replaced, 
the operation of the unit must be checked.

Check unit operation as outlined in the following instructions. If 
any sparking, odors or unusual sounds are encountered, turn off 
electrical power and recheck for wiring errors or obstructions in 
or near the blower motors. Duct covers must be removed before 
operating unit.

Heat Anticipator Setting

Set the heat anticipator on the room thermostat to 0.4 amps to 
obtain the proper number of heating cycles per hour and to 
prevent the room temperature from overshooting the room 
thermostat setting.

Rollout Protection Control

The rollout protection device opens, cutting power to the gas 
control valve, if the flames from the burners are not properly 
drawn into the heat exchanger. The rollout protection device is 
located on the burner bracket. The reason for elevated 
temperatures at the control should be determined and repaired 
prior to resetting this manual reset control.

Rollout Protection on Burner Bracket

Propane Gas Piping Chart II

Tubing Size, O.D. Type L

Nominal Pipe Size Schedule 40

Pipe or Tubing Length—ft (m)

³⁄₈

"

¹⁄₂

"

⁵⁄₈

"

³⁄₄

"

⁷⁄₈

"

¹⁄₂

"

³⁄₄

"

1"

1

¹⁄₄

"

1

¹⁄₂

"

10 (3)

49

110

206

348

539

291

608

1,146

2,353

3,525

20 (6.1)

34

76

141

239

368

200

418

788

1,617

2,423

30 (9.2)

27

61

114

192

296

161

336

632

1,299

1,946

40 (12.2)

23

52

97

164

253

137

284

541

1,111

1,665

50 (15.2)

20

46

86

146

224

122

255

480

985

1,476

60 (18.3)

19

42

78

132

203

110

231

436

892

1,337

80 (24.4)

16

36

67

113

174

94

198

372

764

1,144

100 (30.5)

14

32

59

100

154

84

175

330

677

1,014

125 (38.1)

12

28

52

89

137

74

155

292

600

899

150 (45.7)

11

26

48

80

124

67

141

265

544

815

200 (61)

10

22

41

69

106

58

120

227

465

697

250 (76.2)

9

19

36

61

94

51

107

201

412

618

300

8

18

33

55

85

46

97

182

374

560

350

7

16

30

51

78

43

89

167

344

515

400

7

15

28

47

73

40

83

156

320

479

Goodman 102

To prevent property damage or serious personal injury 
due to fire or explosion caused by a propane gas leak, 
install a gas detecting warning device.
If the propane gas unit is installed in an excavated area 
or a confined space, a warning device is required due to:

-Propane gas is heavier than air and any leaking gas 

can settle in any low areas or confined spaces.

-Propane gas odorant may fade, making the gas 

undetectable except with a warning device.

WARNING

A. Rollout protection

Goodman 94

To avoid property damage, personal injury or death due 
to fire or explosion, a qualified servicer must investigate 
the reason for the rollout protection device to open 
before manually resetting the rollout protection device.

WARNING

A

Summary of Contents for Gold WGGE45





























Reviews: