3
INSTALLATION REQUIREMENTS
Tools and Parts
G
ather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools nee
d
e
d
for connecting the water inlet hoses
■
Pliers (that open to 1
9
/
16
" [39.5 mm])
■
Flashlight (optional)
Tools nee
d
e
d
for connecting the
d
rain hose
■
Locking pliers (that open to 1
9
/
16
" [39.5 mm])
Tools nee
d
e
d
for installation
■
Open end wrenches 14 mm and 13 mm
■
Level
■
Wood block
■
Ruler or measuring tape
Parts supplie
d
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free number
on the cover or in the “Assistance or Service” section.
Options
Pe
d
estal
You have the option of purchasing pedestal separately for this
washer. You may select a 10" (254 mm) or a 15.5" (394 mm)
pedestal. The pedestal will add to the total height of the washer.
Optional pedestal
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your washer or
refer to the “Assistance or Service” section. Ask for Part Number
8572546.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See “Drain
System.”
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will nee
d
■
A water heater set to deliver 120°F (49°C) water to the washer.
■
A grounded electrical outlet located within 6 ft. (1.8 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■
Hot and cold water faucets located within 4 ft. (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
■
A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
■
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs. (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
A. Drain hose form
B. Inlet hose (2)
C. Inlet hose washer (4)
D. Drain hose
E. Transport bolt hole plug (4)
F. Beaded strap
G. Hose clamp
If You Have
You Will Nee
d
to Buy
Laundry tub or
standpipe taller
than 96" (2.4 m)
Sump pump system (if not already
available)
Overhead sewer
Standard 20 gal. (76 L), 30" (762 mm) tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain
Siphon break, Part Number 285320;
additional drain hose
Part Number 8318155; and connector
kit, Part Number 2858835
Drain hose too
short
4 ft. (1.2 m) drain hose extension kit,
Part Number 2858863
Water faucets
beyond reach of fill
hoses
Longer water fill hose:
10 ft. (3.0 m) Part Number 8212656RP
A
B
D
G
C
E
F
Pe
d
estal
Height
Approximate
Height with
Washer
Color
Mo
d
el
Num
b
er
10" (254 mm)
46" (1168 mm)
White
MHP1000SQ
15.5" (394 mm)
51.5" (1308 mm)
White
XHP1550VW
