background image

 

 

 

 

SUMMARY 
 

 
 

1.  GENERAL WARNINGS                                                                          pg.3 

 

2.  SPECIAL WARNINGS FOR POSITIONING AND WIRING THE APPLIANCE         pg.3 

 

3.  POSITIONING                                                                                     pg.4 

 

4.  LEGAL PROVISIONS AND DIRECTIVES                                                    pg.4 

 

5.  ELECTRICAL AND EQUIPOTENTIAL WIRING                                             pg.4 

 

6.  WATER CONNECTIONS                                                                        pg.5 

 

7.  GENERAL OPERATING INSTRUCTIONS                                                   pg.5 

 

8.  CLEANING AND CARE                                                                          pg.6 

 

9.  CONTROL PANEL                                                                                pg.6 

 

10. USE AND FUNCTIONS                                                                          pg.7  

 
 
 
 
 
 
 
 
 
 
 
 
The manufacturer declines all responsibility for any printing or copying errors in this handbook. 
The  manufacturer  reserves  the  right  to  make  any  changes  deemed  necessary  or  useful  to  its 
products without altering the basic features. 
All  rights  reserved.  No  part  of  this  publication  may  be  reproduced  or  photocopied  without  prior 
permission from the manufacturer. 

Summary of Contents for Design Series








Reviews: