background image

9

IMPORTANT:

 Observe all governing codes and ordinances.

This installation must conform with all local codes and  
ordinances. In the absence of local codes, installation must 
conform with American National Standard, National Fuel Gas 
Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association 

One Batterymarch Park, Quincy, MA 02269

CSA International 

8501 East Pleasant Valley Road 

Cleveland, Ohio 44131-5575

The design of this dryer has been certified by CSA International 
for use at altitudes up to 10,000 feet (3048 m) above sea level 
at the B.T.U. rating indicated on the model/serial plate. Burner 
input adjustments are not required when the dryer is operated 
up to this elevation.

When installed above 10,000 feet (3048 m), a four percent 
(4%) reduction of the burner B.T.U. rating shown on the model/
serial plate is required for each 1,000 foot (305 m) increase in 
elevation. For assistance when converting to other gas types 
and/or installing above 10,000 feet (3048 m) elevation, contact 
your local service company.

Gas Supply

GAS DRYER INSTALLATION REQUIREMENTS

Summary of Contents for CGM2745FQ





























Reviews: