Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
%
without “Rapid”
with “Rapid”
Mixed
40
4,0
48
0,50
1:00
-
55
Cotton
95
7,0
74**
2,20
2:30
-
55
Cotton
60
7,0
54
1,19
2:20
1:35
Cotton
40
7,0
66
0,75
2:05
1:15
Synthetics
60
3,0
46**
0,90
1:35
1:10
35
Synthetics
40
3,0
42
0,50
1:20
0:55
Delicates
40
1,5
60
0,65
0:50
-
Delicates
30
1,5
60
0,40
0:46
-
Wool/Handwash
40
1,0
45
0,55
0:40
-
Jeans
40
4,0
52
0,50
1:30
1:10
White
40
7,0
68
0,80
2:20
-
Light colours
40
4,0
60
0,45
1:20
-
Dark
40
4,0
40
0,55
1:40
1:15
Speed 15´
30
3,0
25
0,15
0:15
-
AquaEco
40
3,0
19
0,45
1:00
-
Cotton *
60
7,0
52
0,91
4:00
-
53
Cotton *
60
3,5
40
0,85
3:00 ***
-
Cotton *
40
3,5
40
0,65
3:00 ***
-
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default
setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption
data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
*
Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Load the laundry, add detergent and turn the programme selector
to the desired programme; the “
Start/Pause
” indicator blinks.
The
temperature
and
spin speed
indicated on the display can
be altered by pressing the “Temperature” button or the “Spin”
button. If you do not use the “Dosing Aid”, add detergent now.
If you do not start the programme soon after having made your
choice, the washing machine will switch off automatically after
about a quarter of an hour. To switch the washing machine on
again, turn the programme selector to “O” and afterwards to the
desired programme again.
SELECT ANY DESIRED OPTION
When the combination of programme and additional option(s) is
not possible, the indication switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Colours 15°” button
• Saves energy used for water heating while maintaining a good
wash result.
• Supports colour maintenance when washing coloured laundry.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
• Not selectable for Cotton 70 - 95°C.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 70 - 95°C.
“Prewash” button
• Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
• Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Soil level” button
• Adapts the programme duration to the soil level of your
laundry. Also influences the detergent quantity.
= lightly soiled -
= normally soiled -
= heavily soiled
Not all soil levels are selectable for each programme.
“Spin” button (incl. “Rinse hold”)
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed “0”, the final spinning is cancelled
and the water is drained out only. However, intermediate spin
phases remain during the rinse.
• If you select “Rinse hold”, the laundry remains in the last rinse
water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
-
The wash programme stops to “Rinse hold” when the “Rinse
hold” symbol on the display blinks; the light of “
Start/Pause
”
button also blinks.
-
To terminate the „Rinse hold“ by spinning the laundry, press
“
Start/Pause
” - the laundry will be spun with the default spin
speed. You can also select another spin speed with the „Spin“
button before you start the spin cycle by pressing “
Start/
Pause
”.
PROGRAMME START
Open the tap and press the “
Start/Pause
”
button. The indication
lamp next to the “
Start/Pause
”
button lights up.
CHILD LOCK
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “O” position. To activate the child lock:
• Turn the programme selector to a programme position, or run
a programme as usual.
• Press and hold the 2 buttons marked with the key symbol
simultaneously for a few seconds. A key-like symbol will
shortly appear on the display to indicate that the child lock is
active.
Any time you try to change a programme setting with active child
lock, the display will briefly show the key-like symbol. The
programme setting cannot be changed anymore. The only change
possible is to switch the washer off by turning the programme
selector to the “O” position.
• To deactivate the child lock, proceed in the same way as for
activating it.
FAILURE INDICATION
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“
Water tap closed
”: no or not sufficient inlet water
”
Service
”: failure or malfunction of an electrical component
”
Clean pump
”: waste water is not pumped out.
Spin speed on display blinks
: unbalance during spinning.
PROGRAMME END
The “Door open” indicator lights up, and the display shows “End”.
After about a quarter of an hour, the washing machine will switch
off completely to save energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
DETERGENT OVERDOSAGE INDICATION
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time.
If the symbol lights up and the display shows “Fod”, too much
foam interrupted the wash process; refer to the “Troubleshooting
Guide” in your Instructions for Use.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “
Start/Pause
” button to pause the programme. The
light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the “
Start/Pause
” button again. The new programme
continues at the same position where the previous programme
was interrupted. Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “
Reset/Drain
” button cancels a programme before the end.
• Press and hold the “
Reset/Drain
” button for a few seconds; an
animation appears on the display. The water is drained out; it
may last some time until you can open the door.
CONSUMPTION DATA
Power consumption in off-mode 0,16 W / in left-on mode 0,16 W.
-
To terminate the „Rinse hold“ by draining the water without
spinning, press the „Spin“ button until spin speed „0“ appears
on the display; then press “
Start/Pause
” to start the draining.
-
Do not leave the laundry to soak for too long in the “Rinse
hold” (especially silk).
SET CYCLE END
With this function you can postpone your programme to complete
at a later time: press the button to select in how many hours
the programme shall be finished. Thus, it allows you to have
your laundry ready at a particular time and to profit from more
favorable energy rates during the night, for example. Do not use
liquid detergent when activating “Cycle end” option.
• The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button to
loop through all the available times. To remove it again, keep
on pressing the button until you see the value “0:00”.
• When you have selected the desired time until the “Cycle end”,
press “
Start/Pause
” - the countdown will begin.
• During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.).
If the modifications prolong the programme duration so that it
overruns the originally set time until the “Cycle end”, the
programme will start immediately.
• Sometimes the programme may finish before the selected time
until the “Cycle end” has expired (e.g. for small loads). In this
case, the washing machine will tumble the laundry regularly to
keep it fresh, until the selected “Cycle end” time has expired.
During tumbling, the display will show an animation. The
tumbling phase can be stopped at any time either by pressing
any button or by rotating the programme selector; the
animation will stop and the door will unlock in about 1 minute
as indicated on the display.
DETERGENT DOSING RECOMMENDATION
With the “
Dosing Aid
” button, you can make your washing
machine indicate you the recommended detergent quantity for
your wash load, depending on the soil level selected and the size
of the load.
• Helps to save detergent and protect the environment and also
sensitive skin by avoiding detergent overdosing.
• Before you use this function, you must adapt the washing
machine to the dosing amounts which are recommended
for the detergents you use. Also check if your region’s water
hardness corresponds with the water hardness level “soft” of
your washing machine - if not adapt it.
• Select programme, options and start delay BEFORE using the
“
Dosing Aid
” button.
For any details, refer to the separate “
Dosing Aid
” Instructions
for Use.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to
show the the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during a
running programme, refer to “Reset” a running programme before
the end”.
ECO MONITOR
The “Eco monitor“ gives you a rough feedback about the power
consumption of the programme setting you selected. As soon as
you turn the programme selector to any programme, the “Eco
monitor“ is on.
The indicator on the left is to show that the “Eco monitor“
is active. The four indicators next to it show the degree of
consumption: the less power your programme setting is
forecasted to consume, the less indicators will light up. This
depends on the programme, temperature and options selected,
and also on the size of the wash load. For that reason, the
forecasted degree of power consumption may adapt when the
washing machine detects the wash load.
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
