5019 301 06372
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
1.
Turn the programme selector to the desired programme
and temperature.
2.
The time display shows the duration of the chosen
programme (in hours and minutes), and the “Start (Pause)”
indication lamp
blinks.
3.
The indication lamp of the predefined spin speed lights up.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Eco” button
• With a modified temperature profile and a prolonged
programme duration, the optimum combination of good
washing result and lower energy consumption is achieved.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics” and “Daily
load” programmes to make ironing easier.
• Increases the water quantity and the clothes are spun very gently.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft water,
washing baby linen and helps people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
• This option is particularly recommended for the programmes
“Synthetics”, “Daily load” and “Delicates”.
• It is particularly useful if you want to postpone spinning to a
later time, or if you want to drain only.
• If you select “Rinse hold” do not leave the laundry items to
soak for too long.
Note: The programme stops to “Rinse hold” at the time the
“Rinse hold” light in the programme sequence indication is on.
The indication lamp next to the “Start (Pause)” button
blinks.
Terminate the “Rinse hold” option
:
• Press the “Start (Pause)” button
; the programme will
terminate automatically with the final spin cycle for the present
wash programme.
• If you do not wish to spin the clothes, turn the programme
selector to the “Drain” programme and press the “Start
(Pause)” button
.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)*
Cotton / Antibacterial
95
max.
59**
1.90
2:00
Cotton
60
max.
49
1.02
2:20
Cotton with “Eco”***
60
max.
49
0.90
4:00
Cotton
40
5.0
56
0.70
2:00
Synthetics
60
2.5
50**
0.80
1:35
Synthetics
40
2.5
46
0.50
1:20
Delicates
30
1.5
60
0.50
0:45
Daily load
40
3.0
41
0.50
1:00
Quick wash
30
3.0
41
0.40
0:30
Wool
40
1.0
60
0.50
0:45
Handwash
40
1.0
45
0.50
0:40
Lingerie
30
1.0
45
0.40
0:36
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
The “Start delay”
allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay time by 1 to
23 hours.
• Press the “Start (Pause)” button
.
The countdown of the delay time begins; the “Start delay”
indication lamp and the dot on the display will keep blinking
until the programme starts.
• The time delay indication disappears when the programme starts
and it is replaced by the remaining programme time.
• Once having pressed the “Start (Pause)” button
, the
number of hours preselected can be reduced by pressing again
the “Start delay” button.
To cancel the “Start delay”
...before you press the “Start (Pause)” button
:
• Turn the programme selector to another position or press the
“Reset” button
.
...after having pressed the “Start (Pause)” button
:
• Press the “Reset” button
for at least 3 seconds - the
start delay time disappears from the time display.
Open the tap and press the “Start (Pause)” button
. The
indication lamp of the “Start (Pause)” button
lights up. The
programme sequence indicator shows the current programme
phase, running from left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining time is
newly calculated in certain programme phases. If this is the case, an
animation appears on the time display.
Before starting and after end of a programme, the lamp lights to
show that the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Guide” in your
Instructions for Use; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water
tap; if the indication still lights up, refer to the “Troubleshooting
Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned; in the latter case refer to the
Instructions for Use (“Removing the Filter”).
•
All the lights of the programme sequence indicator are off,
and the “Door open” indication
lights up.
1.
Turn the programme selector to the “Off/O” position.
2.
Close the water tap.
3.
Open the door and unload the machine.
4.
Leave the door ajar to allow the drum to dry.
1.
Press the “Start (Pause)” button
to pause the
programme. The light blinks.
2.
Select the new programme (with temperature), any options
and another spin speed if you want.
3.
Press the “Start (Pause)” button
again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The “Reset” button
cancels a programme before the end.
•
Press the “Reset” button
for at least 3 seconds; “rES”
appears on the display. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106372GB.fm Page 2 Tuesday, April 20, 2010 10:22 AM
Black process 45.0° 150.0 LPI
