background image

5019 301 10453

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as 
described in the chapter “Detergent and Additives” 
in your Instructions for Use.
Close the door and turn the programme selector to the 
desired programme and temperature. The indication 
lamp next to the “Start/Pause” button 

 flashes.

Push the button(s) of any option(s) desired - the 
respective indication lights up.
When the combination of programme and additional 
option(s) is not possible, the indication lights switch 
off automatically. Unsuitable combinations of 
options are deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly 

prolonged washing duration, the optimum 
combination of excellent washing result and even 
lower energy consumption is achieved.

“Prewash” button
• Only for heavily soiled loads (for example sand, 

granular dirt) sensible. Increases the cycle time 
by approximately 15 min.

• Do not use liquid detergent for the main wash 

when activating the Prewash option.

“Intensive rinse” button
• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with 

very soft water, washing baby linen and helps 
people with allergies.

“Rinse hold” button
• The laundry remains in the last rinse water 

without progressing to the final spin cycle to avoid 
creasing and prevent colours from changing.

• This option is particularly recommended for the 

programmes “Synthetics”, “Daily load” and 
“Delicates”.

• It is particularly useful if you want to postpone 

spinning to a later time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at 
the time the “Rinse hold” light in the programme 
sequence indication is on. The indication lamp 
next to the “Start/Pause” button 

 flashes.

Terminate the “Rinse hold” option

:

• Press the “Start/Pause” button 

; the 

programme will terminate automatically with the 
final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the 

programme selector knob to the “Drain” programme 
and press the “Start/Pause” button 

.

“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is 

cancelled but intermediate spin peaks remain 
during rinse. The water is drained out only.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

Cotton

95

5.0

49*

1.90

2:00

Cotton

60

5.0

44

0.95

2:10

Cotton with “Eco”**

60

5.0

44

0.85

2:20

Cotton

40

5.0

44

0.60

2:00

Synthetics

60

2.5

50*

0.70

1:30

Synthetics

40

2.5

45

0.55

1:15

Delicates

30

1.5

50

0.50

0:45

Daily load

40

3.0

45

0.45

1:00

Quick wash

30

3.0

40

0.40

0:30

Wool

40

1.0

55

0.60

0:45

Handwash

40

1.0

45

0.60

0:40

Handwash

30

1.0

45

0.50

0:40

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home 

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

*

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

**

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR 
AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start Delay” 

 allows to run the machine at 

the consumer’s convenience, for example at night 
when electricity is cheaper. Do not use liquid 
detergent when activating the start delay.

• Select programme, temperature and options.

• Press the “Start delay” button to select the delay 

time by 1, 3, 6, 9 or 12 hours.

• Press the “Start/Pause” button 

The indication  next to the “Start delay” button 
flashes and goes off when the programme starts.

• Once having pressed the “Start/Pause” button 

, the countdown of the time delay begins. 

When the programme starts, the start delay 
indicator light goes off and is replaced by the 
programme sequence indication.

• After the “Start/Pause” button 

 has been 

pressed, the number of hours preselected can be 
reduced by pressing again the “Start delay” button.

To cancel the “Start delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another 

position or press the “Reset” button 

.

..after having pressed the “Start/Pause” button:

• Press  the “Reset” button 

 for at least 3 

seconds - the start delay indicator light goes out.

Open the tap and press the “Start/Pause” button 

. The indication lamp next to the “Start/Pause” 

button 

 lights up. The programme sequence 

indicator shows the current programme phase, running 
from left to right through Wash, Rinse, Spin/Drain.

When the programme phase is finished, the 
corresponding indication goes out.

Before starting and after end of a programme, the 
lamp lights to show that the door can be opened. As 
long as a wash programme is running, the door 
remains locked and must on no account be forced 
open. In case you have an urgent need to open it 
during a running programme, refer to “Cancel 
(Reset) a running programme before the end”.

“Water tap closed”
The appliance has no or insufficient water supply. 
Open the water tap; if the indication still lights up, 
refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned; in 
the latter case refer to the Instructions for Use 
(“Removing the Filter”).
“Service”
Lighting up of the “Service” indication can be caused by 
a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your Instructions for Use; if 
the fault persists, contact our After Sales Service.

All the lights of the programme sequence 
indicator are off, and the “Door open” 
indication 

 lights up.

1. Turn the programme selector to the “Off/O” 

position.

2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.

1. Press the “Start/Pause” button 

 to pause 

the programme. The light flashes.

2. Select the new programme (with temperature), 

any options and another spin speed if you want.

3. Press the “Start/Pause” button 

 again. The 

new programme continues at the same position 
where the previous programme was interrupted. 
Do not add detergent for this programme.

The “Reset” button 

 cancels a programme 

before the end.

Press  the  “Reset” button 

 for at least 3 

seconds. Any existing water is drained out 
before the door can be opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME START

CANCEL (RESET) A RUNNING 
PROGRAMME BEFORE THE END

Reviews: