background image

24

Dosage

Follow the instructions on the detergent pack in 

relation to:

•

the degree and type of soiling;

•

the size of the load:

•

full load: follow the detergent manufacturer’s 

instructions;

•

half load: 3/4 the amount used for a full load;

•

minimum load (about 1 kg): half the amount 

used for a full load;

•

water hardness in your area (ask for information 

from your water company): soft water requires 

less detergent than hard water.

Notes:

Too much detergent can result in excess foam 

formation, and the reduction of washing 

efficiency. If the appliance detects excessive foam 

it may prevent spinning.

Insufficient detergent may result in: grey laundry, 

deposits on the drum, tub and heater.
You can use liquid detergent in the “Prewash” 

phase for programmes with this option. In this 

case put only powder detergents in the 

compartment for the main wash 

.

When using concentrated fabric softeners, add 

water in the detergent dispenser up to “MAX” level 

mark.
To prevent dispensing problems when using highly 

concentrated powder and liquid detergents, use 

the special detergent ball or bag supplied with the 

detergent and place it inside the drum.

For machine with three chambers detergent dispenser: adjust the water hardness level pointer in the 

detergent dispenser in accordance with the hardness of the water in your area. Move the pointer sideways 

to the required position.

Water hardness: 

soft water requires less detergent

Water hardness 

area

Characteristics

German scale 

°dH

French scale 

°fH

Clarke scale 

°eH

1

2

3

4

soft

average

hard

very hard

0-7

7-14

14-21

over 21

0-12

12-25

25-37

over 37

0-9

9-17

17-26

over 26

Filling the detergents and additives

1.

Pull out the detergent dispenser to its full extent.

The dispenser will have three or four chambers depending on 

model.

2.

Fill the detergent:

•

Programme with pre- and main wash

 

•

Main wash programme without prewash

 

When using liquid detergent, remove the coloured 
insert and fit it in the compartment.

 

The graduate scale on the insert makes dosing easier. 

•

Fabric softeners and conditioners, no more than

to “MAX” mark (three chambers model 

“B

”) 

or the “100 ml” mark (four chambers model 

“A

”).

•

Chlorine bleach, no more than to “MAX” mark
(four chambers model 

“A

”).

•

Stain remover agents

•

Water softeners (water hardness class 4)

•

Starch (dissolved in water)

3.

Close the detergent dispenser completely.

A

B

3gb05221.fm5  Page 24  Tuesday, September 4, 2001  6:13 PM

Summary of Contents for AWM276


















Reviews: