background image

2

recirculation mode. You can find the charcoal filter in the carton box.   

* Only a qualified and trained service technician can undertake the 

work of installation and servicing. 

* This appliance can not use extend cord. 

* Check that the mains voltage corresponds to the one indicated on 

the rating plate fixed inside the hood. 

*  Check  that  the  domestic  power  supply  guarantees  adequate 

earthing. 

*  Do  not  connect  the  hood  to  exhaust  ducts  carrying  combustion 

fumes (boilers, fireplaces, etc.) 

* If the hood is used in conjunction with non-electrical appliances (e. 

g. gas burning appliances), a sufficient degree of ventilation must be 

guaranteed in the room in order to prevent the backflow of exhaust 

gas. The kitchen must have an opening directly with the open air in 

order to guarantee the entry of clean air. 

* The minimum distance is 750mm from the cooker hood to a gas 

hob, and is 650mm to an electric hob. If the installation instructions 

for gas/electric hobs  specify a greater distance the  same must be 

taken into account. 

 

NOTICE:

  Considering  excessive  weight,  two  or  more  people  are 

required to install or move this appliance. Failure to do so can cause 

physical injuries and damage to the product. 

 

USE 

*  The  cooker  hood  has  been  designed  only  for  domestic  use  to 

eliminate kitchen fumes. 

*  Never  use  the  hood  for  purposes  other  than  what  it  has  been 

designed for. 

*  Never  leave  high  naked  flames  under  the  hood  when  it  is  in 

operation. 

* Adjust the flame intensity to direct it onto the bottom of the pan 

only make sure that it does not engulf the pan sides. 

*  Deep  fat  fryer  must  be  continuously  monitored  during  use: 

Summary of Contents for AKR912CIXM















Reviews: