background image

INSTALLATION INSTRUCTIONS

30" (76 CM) FREESTANDING GAS RANGES

RANGE SAFETY

Table of Contents

RANGE SAFETY.................................................................. 1

INSTALLATION REQUIREMENTS .................................... 2

Tools and Parts................................................................ 2
Location Requirements....................................................3
Electrical Requirements ................................................... 4
Gas Supply Requirements............................................... 5

INSTALLATION INSTRUCTIONS ......................................6

Unpack Range ................................................................. 6
Install Anti-Tip Bracket.....................................................6
Verify Anti-Tip Bracket Location......................................7
Level Range ..................................................................... 7
Make Gas Connection .....................................................7

Electronic Ignition System ................................................... 8
Replace Oven Racks and Storage or Warming Drawer ... 10
Complete Installation......................................................... 10

GAS CONVERSIONS............................................................ 11

Convert from Natural Gas to LP Gas ................................ 11
Replace Oven Racks and Storage or Warming Drawer ... 13
Complete Installation......................................................... 13
Convert from LP Gas to Natural Gas ................................ 13
Replace Oven Racks and Storage or Warming Drawer ... 14
Complete Installation......................................................... 14

ANTI-TIP BRACKET TEMPLATE  ....................................... 16

IMPORTANT: 
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
Save installation instructions for local electrical inspector's use.

9762998

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

Summary of Contents for 9762998

















Reviews: