background image

Xcavator

 Operating Instructions 

3

Familiarization

Control Panel 

Access Door

  1.  Ready indicator
  2.  100 Gram cycle start key (cool mold)
  3.  200 Gram cycle start key (cool mold)
  4.  100 Gram time delay before start indicator (hot mold)
  5.  200 Gram time delay before start indicator (hot mold)
  6.  Abort cycle key
  7.  Exhaust flow Indicator
  8.  Depth of cut selector switch

Setup

Air Supply

1.  Connect your compressed air supply to the air regulator 

inlet hole shown in the photograph (Figures 1A and 1B). 
The inlet hole is a standard 1/8" National Pipe Thread (NPT).

Air Regulator

Setpoint Adjust

2.  With air supply connected, pull knob upward, and 

rotate it until gauge needle points to 35 psi (Figure 2).

nOTE: THIS MAy nEED TO BE RE-ADjuSTED SlIGHTly  
OnCE BEAD FlOW IS ESTABlISHED.

 

Push knob back downward after pressure is set.

Daily Moisture Bowl Check

3.  Pressing upwards on the black plastic ring at the bottom 

of the air regulator opens up a check valve and allows 
accumulated moisture to drain from the clear plastic 
accumulator bowl (Figure 3). It is very important to keep 
drained so that moisture does not pass through to the 
bead reservoir. Moist beads will adhere to each other 
and prevent transfer to the nozzle.

1

2

6

3

7

4

8

5

Figure 2

Figure 3

Figure 1A

Figure 1B

Summary of Contents for Xcavator

















Reviews: