background image

14

Turn off the power to the oven, unplug the power cord, 

remove trays from the muffle chamber and insure that 

the oven is cool .
Remove the upper back cover .
On the rear of the unit remove the nuts that hold the 

heater plate wires to the ceramic terminals . Remove all 

hardware and wires from the terminals . Discard any 

burnt hardware and replace with hardware pieces 

shipped with the heater plates . Retain hardware for 

later use . Straighten the wires for smoother removal 

of the plates .
Straighten thermocouple at the bend and remove 

bushings from heater plate wires .
Move heater wires and thermocouple out of the 

upper housing to allow insulation to slide out  

the back of the unit .
From the front of the muffle chamber with the door open 

push the entire insulation chamber out the back of unit 

and place on a table .
Remove ceramic front plates from muffle insulation 

and place aside .

 
From here the plates can be removed by pulling them 

out the front of the insulation . The Large models have 

back plates and side plates, while the Medium model 

has only side plates .

 

Place the new plates in the chamber, if back plates are 

being replaced as well they must be installed first, also 

insure that the wires are bent up so they will slide into 

the back .
If the back plates are being replaced the filler strip 

should be replaced as well . A new strip was shipped 

with the plates .

 
Once the plates are installed place the insulation chamber 

back inside the oven and wire the terminals according to 

the model and voltage in the pictures on the next page:
When wiring the plates insure that between each wire 

a flat washer is placed . See picture below .

Note:  Place flat washer between each wire.

After the heater plates are wired, replace the upper back 

cover and bottom cover . Insure that the oven heats by 

running a program .

FIELD SERVICE

REPLACEMENT OF HEATING PLATES

Heater Jumper

Ceramic Fronts

Flat Washer

Flat Washer

Side Heating 

Plate Assembly 

(2)

Ceramic Insulating Bushings

Insulating Strip

Rear Heating 
Plate Leads

Rear Heating 
Plate Leads

Lock Washer

Lock Washer

Nut

Nut

Summary of Contents for P.D.Q.

























Reviews: