manualshive.com logo in svg

Whip Mix Infinity, Operator'S Manual, Page: 22 / 32

Share
Download
Whip Mix Infinity Operator'S Manual Download Page 22

1.  Remove the back panel of the furnace.

2.  Remove the nuts which hold the heating plate wires to the power terminals and straighten the heating 

 

plate wires (Figure 4).

3.  Open the furnace door and find the two ceramic sections at the front of the furnace chamber. Hold the

 

furnace door partially open while removing the ceramic sections. They are not readily removed when the   

 

door is fully open. Remove the right–hand ceramic section by lifting it upward until the bottom of the section  

 

clears the sheet metal housing. Pull the bottom of the ceramic section out, then pull it down so the upper  

 

half clears the sheet metal housing. Remove the left–hand ceramic plate in the same way.

4.  Remove the floor plate, then carefully slide the two side heating plates out the front of the furnace. The two

 

rear heating plates on Infinity L–30 may now be removed.

5.  Check the condition of the filler strip insulation in the space to the left and right of the ceramic front

 

sections. Replace if required*.

6.  Check the condition of the floor plate which provides insulation and serves as a spacer between the bottom  

 

ends of the heating plates. Replace if required*.

7. To install the new heating plates reverse the procedure. Push the ceramic heating plates back into place on  

 

the rear insulating panel. When reconnecting the heating plate wires at the rear of the furnace, be sure to  

 

replace all hardware in its original position. (Figure 4.) Tighten all connections.

 

*Replacement Part: Floor Plate w/ Filler Strip Insulation

       Infinity M–30: PN 33980; Infinity L–30: PN33981 

FIELD SERVICE

REPLACEMENT OF HEATING PLATES

REPLACEMENT PART NUMBERS

21

 

115V 220/230V 

 

M–30 

(Set of 2) 

33915 

33916 

L–30

Set of 2 Side Plates 

33918 

27957 

Set of 2 Rear Plates 

33917 

27956 

INFINITY M–30 (ALL VOLTAGES)

INFINITY L–30 115 VOLT

INFINITY L–30 220/230 VOLT

22

Figure 4

INFINITY WITH UPPER REAR PANEL REMOVED

Heating Plate Wire

Power Terminal

Heater (Power) Leads

Rear Insulating Panel

Thermocouple

Thermocouple Clamp

Ceramic Insulating 
Bushing

Insulating Filler

Rear Insulating Panel

Thermocouple

Thermocouple Clamp

Ceramic Insulating 
Bushing

Insulating Filler

Heating Plate Wire

Power Terminal

Heater (Power) Leads

Jumper

Heating Plate Wire

Power Terminal

Heater (Power) Leads

Jumper

Insulating Filler

Ceramic Insulating 
Bushing

Thermocouple Clamp

Thermocouple

Rear Insulating Panel

Summary of Contents for Infinity

































Reviews:

No comments