Page 3
Lightbar Cable:
The standard lightbar uses an 11 conductor cable for LED’s and Halogens as well as
power and function. Extend the cable towards your switch panel and follow the
switch panel instructions for wiring connections. Cigar cord models do not offer Low
Power or Pattern Override. On cigar plug models Scan-Lock™ is controlled by a
momentary switch on the cigar plug.
WARNING! All Customer supplied wires that connect to the positive terminal of
the battery must be sized to supply at least 125% of the maximum operating
current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
VIOLET - Low Power:
The type of switch used depends on how you wish Hi/Lo to function:
Latching Mode:
Apply positive voltage to the VIOLET wire for less than 1 sec., the
lightbar is “latched” into low power. The lightbar must be turned off and then back on
to restore normal operation.
(A momentary switch is preferred)
Level Mode:
Applying positive voltage to the VIOLET wire for more than 1 sec. holds
the lightbar in low power mode until voltage is removed.
(A toggle switch is preferred)
WHITE/BLUE - Pattern Override
Ap12 volts to the WHT/BLU wire while lightheads are activated will change
the flash pattern to whichever flash pattern that
pattern override
is pre-programmed
for. To program
pattern override
, activate the lightbar than activate
pattern override
by applying +12 volts to the WHT/BLU wire. Now you may select a flash pattern
using the
Scan-Lock™
procedure.
WHITE/VIOLET - Scan-Lock™
LED’s must be on for Scan-Lock™ to work.
TO CHANGE PATTERNS:
To cycle forward to the next available pattern:
Apply
+VBAT volts to the WHT/VIO wire for less than 1 second and release.
To cycle back
to the previous pattern:
Apply +12 volts to the WHT/VIO wire for more than 1 second
and release.
TO CHANGE THE DEFAULT PATTERN:
When the desired pattern is active, allow it
to run for over 5 seconds. The lightbar will now display this pattern when activated.
TO RESTORE THE FACTORY DEFAULT PATTERN:
With power to the lightheads
off, apply +12 volts to the WHT/VIO wire. While still ap12 volts to the WHT/
VIO wire, turn power to the lightheads back on. The factory default pattern should
now be displayed.
A Normally Open momentary switch can be used to control Scan-Lock™
operation. Cigar cord models have a switch on the cigar plug.
RED - Front Warning Lights:
Ap12 volts to the RED wire activates the Front Warning lights.
WHT - Drivers Alley Light:
Ap12 volts to the WHT wire activates the Drivers Side Alley Light.
YEL - Passengers Alley Light:
Ap12 volts to the YEL wire activates the Passenger Side Alley Light.
BLK/YEL - Rear Warning Lights:
Ap12 volts to the BLK/YEL wire activates the Rear Warning Lights.
WHT/BLK - Takedowns:
Ap12 volts to the WHT/BLK wire activates the Takedowns.
IMPORTANT! Before returning this vehicle to active service, visually confirm
the proper operation of this product, as well as all vehicle components/
equipment.
IMPORTANT! It is the responsibility of the installation technician to make sure
that the installation and operation of this product will not interfere with or
compromise the operation or efficiency of any vehicle equipment!
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
I M P O R TA N T W A R N I N G !
VI
O
WH
T/
BL
U
WH
T/VI
O
G
R
Y
BL
K
BL
K/
WH
T
RED
WH
T
Y
EL
BL
K/Y
EL
WH
T/
BL
K
Low
Power
Pattern
O
v
err
i
de
S
can
-
Lock
™
Ha
l
ogen
/
Co
mm
on
(G
round
)
Warn
i
ng
L
i
ghts
(G
round
)
Warn
i
ng
(G
round
)
Front
Warn
i
ng
L
i
ghts
(+12V
DC
)
Dr
iv
ers A
ll
ey
(+12V
DC
)
Passengers A
ll
ey
(+12V
DC
)
Rear
Warn
i
ng
L
i
ghts
(+12V
DC
)
T
akedowns
(+12V
DC
)
App
l
y
+12V
DC
to
step
down
to
Low
Power
App
l
y
+12V
DC
to
sw
i
tch
to
Pattern
O
v
err
i
de
S
can
-
Lock
™ /
F
l
ash
Pattern
S
e
l
ect
i
on
3 A
m
p
Fuse
Wi
re
Co
l
or Funct
i
on
Op
erat
i
on
1
A
m
p
Fuse
A
ll f
uses
and
sw
i
tc
h
es
are custo
m
er su
ppli
ed
W i
r
i
n g
Di
agra
m
Justice™ Mini-Lightbar
BA
TT
ER
Y
S
P
S T
S
w
i
tch
Mounting bracket angle is adjustable 7.5° to eit
h
er side
An alley lig
h
t is s
h
own.
LE
D
Takedown
C
O
N3 LE
D
BA
S
E
Re
m
o
v
e
do
m
e
LR11 / Re
m
oval & Installation / Alley Lig
h
t
4 - 4 0
X 3/8
To r x
Head
Re
m
o
v
e
d o
m
e
s c r e w s
(
QT
Y
6
)
3
1
2
LR-11 LE
D
/ Angle Adjust
m
ent
Re
m
o
v
e screws
and pull housing
part
way
out.
