Page 2
Insert foot into extrusion
with locking plate
attached.
Twist foot into
position
ANCHOR
PLATE
Fig. 2
Fig. 3
Loosely secure foot and anchor plate.
Fig. 4
slide foot
under lip
S t r a p
Mount
o n l y
Mounting
Pad
1/4 INTERNAL
TOOTH LOCK
WASHER
1/4 - 20 X 1-1/2
PHILLIPS PAN
HEAD METAL
SCREW
1/4 - 20 X 7/16 HEX NUT
Locking
Plate
Fig. 1
Tighten Allen
Set Screws
to 14-16 In.Lbs.
Fig. 1
Bottom of
Extrusion
MOUNTING
SURFACE
1/2 - 13 Hex Bolt
1/4 - 20 X 5/8 Square
Hd Set Screw
Mounting
B r a c k e t
1/2" Split Lock Washer
1/2" Flat Washer
1/2 - 13 X 2-3/4
Hex Head Bolt
Permanent Mounting:
1.
Locate the mounting foot and locking plate included with your lightbar. If not already present,
install the locking plate onto the mounting foot using the supplied allen set screws (Fig. 1).
2.
Flip the lightbar upside-down to expose the bottom of the extrusion. Place the mounting
foot into the extrusion and rotate the foot so that the top of the foot swings into position
under the lips in the extrusion (Figs. 2, 3 & 4).
NOTE:
You do not need the anchor plate
shown in Figs. 2 - 4. This is used in strap mounting.
3.
Repeat this procedure for the remaining mounting foot and return the lightbar to its right
side-up position.
4.
Position the lightbar onto the vehicle roof in the desired mounting location. One often selected
location is directly above the B-pillars. This area is the strongest part of the roof. Check the light
bar cable exit location to be sure that the lightbar is facing the proper direction (Cable exits in rear).
5.
Adjust the mounting feet outwards so that they are as close to the edge of the roof as possible (See
below). When the mounting feet are properly positioned, lightly tighten the allen head set screws.
6.
Turn the lightbar upside down and tighten all of the mounting foot allen head set screws (Fig.4) to 14-16 In.
Lbs. With the lightbar upside down, drill 2 holes into the mounting foot (for the mounting bolts) using the holes
in the mounting pads as guides, in the location shown in figure 1.
7.
Place the lightbar in its final mounting position on the vehicle, mark the mounting hole locations off onto the mounting
surface, remove the lightbar and drill the mounting holes. You will need to lower the vehicle headliner (if present) for steps 7 & 8.
8.
Place the lightbar back onto the vehicle lined up with the mounting holes and secure the mounting feet to the vehicle using the supplied hardware.
IMPORTANT! The lightbar should be located a minimum of 16" from
any radio antennas!
Slide Bolt Mounting:
1.
Insert the two supplied 1/2 - 13 X 2-3/4 HEX HD BOLTS into the slide
bolt brackets and twist the two brackets into the bottom of the lightbar
extrusion (Fig. 1).
2.
With the slide bolt brackets in their mounting position, secure them to
the lightbar with the supplied set screws.
3.
Position the lightbar onto the vehicle and mark the location of the two
mounting bolts off onto the mounting surface.
4.
Remove the lightbar and drill the two mounting holes you marked off
using a 1/2” drill bit.
5.
Secure the lightbar to
the mounting surface
with
the
supplied
mounting hardware.
6.
Extend wires to your switch panel and refer to the wiring diagram.
Refer to the instructions included with your switches for switch wiring.
IMPORTANT! It is the responsibility of the installation technician to make
sure that the installation and operation of this product will not interfere
with or compromise the operation or efficiency of any vehicle equipment!
Before returning the vehicle to active service, visually confirm the proper
operation of this product, as well as all vehicle components/equipment.
