Page 2
Pattern Selection Procedure:
IMPORTANT:
Pattern selection requires the L.E.D. to be turned on.
DO NOT LOOK DIRECTLY AT L.E.D.s WHILE UNIT IS IN OPERATION.
1.
Remove the lens and Locate the Pattern Activation Pins for your model
L.E.D. (Section of typical L.E.D. board below shows pins.)
NOTE:
Although the location of the pins varies for each LED board, this
procedure is applicable to all LED boards that offer selectable patterns.
The location of these pins will vary between models, but they will always be
on the LED side of the circuit board. Electrical components will not be
visible on encapsulated LED boards.
2.
Turn the L.E.D. flasher on.
3A.
3B.
3C.
TO CYCLE FORWARD THROUGH ALL PATTERNS:
TO CHOOSE A PATTERN:
TO CYCLE BACKWARDS THROUGH ALL PATTERNS:
Use a penny (or any electrical conducting item) to
contact both Pattern Activation Pins for less than
1 second and release. Repeat for next pattern.
While cycling through the patterns, allow a pattern
to run for more than 5 seconds, this will become
the default pattern until it is changed
Hold penny against Activation Pins for more than 1 second and release.
RAPIDFIRE 375
RAPIDFIRE 150
RAPIDFIRE 75
RAPIDFIRE 30
DOUBLE FLASH 150
DOUBLE FLASH 75
COMET FLASH
ACTION FLASH
MODU FLASH
SIGNAL ALERT 150
SIGNAL ALERT 75
SCAN -
SIGNAL ALERT BRAKE
375 Single Flashes Per Minute
150 Single Flashes Per Minute
75 Single Flashes Per Minute
Single Flashes Per Minute
150 Double Flashes Per Minute
75 Double Flashes Per Minute
75 Comet Flashes Per Minute
2 Comet Flash / 4 X 150 SFP / 2 Comet
75 to 360 Single Flashes Per Minute
150 Flashes Per Minute
75 Flashes Per Minute
2 Cycles of Patterns 3 thru 12
4 Flashes Cycle For 200 MS
™
-
™
-
™
-
™
-
-
-
-
™ -
™ -
™
-
™
-
™
-
30
®
Available Flash Patterns:
4.
When you've choosen a pattern, turn off power and re-mount lens.
Followed by Steady Burn
STANDARD BRAKE
-
Steady Burn
SIGNAL ALERT ARROW 375
SIGNAL ALERT ARROW 150
SEQUENCE ARROW 150
SEQUENCE ARROW 60
375 Flashes Per Minute
150 Flashes Per Minute
150 Flashes Per Minute
60 Flashes Per Minute
™
-
™
-
-
-
ARROW L.E.D. ONLY:
Pattern
Activation
Pins
Installation:
1.
Using the dimensions from the template, mark off and drill the two 5/16 inch
diameter vent tube holes and the 1 inch center wire hole into the mounting
surface.
Make sure lighthead will not interfere with existing equipment and be
aware of any items on the opposite side of the mounting surface.
2.
Insert the two vent tubes extending from the rear of the lighthead into their
holes. Using a scribe or similar tool, mark off the 4 mounting holes.
3.
Using a drill bit sized for a #6 sheet metal screw
(and the thickness of the
mounting surface)
, drill the four mounting holes. Install a grommet
(customer
supplied)
into the 1 inch wire hole.
4.
Using appropriately sized wires
(Minimum wire size / 18 AWG)
, run the
lighthead wires to their connections.
(See the color / function table for the
lighthead being installed)
Fuse the +12VDC connections at 3 Amps and test
the operation of the lighthead before securing it to the vehicle.
5.
Position the lighthead components onto the mounting surface and secure to
the vehicle using four #6 x 1-1/2” sheet metal screws.
Note: This product draws significantly less current than a standard
incandescent automotive bulb. If your flasher does not operate
properly, it may be necessary to replace your existing flasher
module with a Whelen 3TERM flasher module. Contact your
sales representative for specific vehicle application.
WARNING! The outer surfaces of this product may be cleaned with
mild soap and water. Use of any other chemicals may
void product warranty. Do not use a pressure washer.
Specifications:
BRAKE / TAIL / TURN (max)
LED Assembly -
Input Voltage -
.
-
.
.
Default Flash Pattern -
360 LED's
12 8 VDC
Tail - 0 095 AMPS
Brake - 0 72 AMPS
Signal Alert Brake
±20%
Input Current
™
E-SPEC
Input Voltage
Input Current -
Default Pattern -
-
12.8 VDC
0.68
Signal Alert
AMPS
±20%
™
BRAKE / TAIL / TURN (min)
Input Voltage -
.
-
.
.
12 8 VDC
Tail - 0 054 AMPS
Brake - 0 34 AMPS
Default Flash Pattern -
Signal Alert
Brake
LED Assembly /
96 LED's
±20%
Input Current
™
0.700 AMPS
Signal Alert
FLASHER
Input Voltage
.
-
12 8 VDC
Input Current -
Default Pattern -
±20%
™
ARROW
Input Voltage -
.
-
12 8 VDC
0.35 AMPS
±20%
Input Current
™
Default Flash Pattern -
Sequence
Arrow 150
Flood 0.475 AMPS
Back-Up 0.225
Steady
BACK-UP / FLOOD
Input Voltage
.
-
12 8 VDC
Input Current -
Default Pattern -
±20%
™
Input Current -
