SAFEPATH Manual
Sheet 24 of 78
Rev. C April 1999
Single File Download Procedure
1.
Select "TRANSFER FILE" from the main menu on the source Series DV-200.
2.
Select “MESSAGE/STRING” from the next menu.
3.
Select “FILE” from the next menu.
4.
Enter file number of the file to be downloaded.
5.
Repeat step 3 for all files which need to be downloaded.
6. Test the SAFEPATH panel to ensure that all files (messages, output channel assignments, and priority assignments) were
transferred properly by activating all downloaded files.
The length of time required to download each file will vary depending upon the length of the file. String files are typically very short
and should be downloaded within several seconds. Voice files are typically very long. When downloading voice files, a good rule of
thumb is that downloading will require 30 seconds for every second of recorded time.
If for any reason the downloading sequence is interrupted (due to power loss, a disconnected cable, etc.), disconnect input power to
the destination digital voice panel for a minimum of two seconds and then reconnect. If downloading to a DX-200, the partially
transmitted file must be re-downloaded, according to the procedures set forth below. If downloading to a DX-100, the partially
transmitted file must be either disabled or re-downloaded, according to the procedures set forth below. A disabled file may not be
played or re-used without erasing all message memory EPROM's in the DX-100 with an ultraviolet (UV) light source.
All Files Download Procedure
1.
Select "TRANSFER FILE" from the main menu on the source Series DV-200.
2.
Select “MESSAGE/STRING” from the next menu.
3.
Select “ALL” from the next menu.
The length of time required to download each file will vary depending upon the number, types and sizes of the files to be
downloaded. A good rule of thumb is that downloading will require 30 seconds for every second of recorded time.
If for any reason the downloading sequence is interrupted (due to power loss, a disconnected cable, etc.), disconnect input power to
the destination digital voice panel for a minimum of two seconds and then reconnect. If downloading to a DX-200, the partially
transmitted file must be re-downloaded, according to the procedures set forth below. If downloading to a DX-100, the partially
transmitted file must be either disabled or re-downloaded, according to the procedures set forth below. A disabled file may not be
played or re-used without erasing all message memory EPROM's in the DX-100 with an ultraviolet (UV) light source.
CAUTION:
Never disable a file on a DX-200. Disabling a file on a DX-200 will cause the DX-200 to indicate a trouble
condition.
File Disable Procedure (DX-100 Only)
1.
Select "TRANSFER FILE" from the main menu.
2.
Select "REMOVE" from the incomplete file menu.
File Re-Download Procedure
1.
Select "TRANSFER FILE" from the main menu.
2.
Select "REXMIT" from the incomplete file menu.
If the re-download attempt fails when re-downloading to a DX-100, the file must be disabled.
System Configuration Data Download Procedure
1.
Select "TRANSFER FILE" from the main menu on the source Series DV-200.
2.
Select “CONFIGURATION” from the next menu.
Summary of Contents for SAFEPATH SAPE-1AB
