Wheelock PRM-150 Installation Instructions Download Page 4

P81537 G 

Sheet 4 of 5 

 

PRE-AMP

-2
4

V

T-
IN

R-
IN

GND

R-
OUT

T-
O

U

T

1    2    3    4    5    6

TO 24VDC

POWER SUPPLY

INPUT TO

AUDIO 

SOURCE

OUTPUT TO

 SPEAKER

AMPLIFIERS

 

 

Figure 7: 

Simplified Schematic And Connection Diagram 

 
 
OPERATION: 

 
1. 

Set PRM-150 volume control to position #5. 

 

2. 

Adjust each Speaker Amplifier's volume control to the desired volume level. 

 

3. 

If the desired volume level cannot be obtained at any or all speaker-amplifiers, then: 

 

(A)  Increase the PRM-150 volume control setting until the desired volume level is obtained at the speaker-amplifier(s) which 

had the least volume. 

 

(B)  Readjust the other Speaker Amplifier volume controls, as required. 

 
 

TROUBLE SHOOTING: 

 
CONDITION CHECK 
 
1.  No audio output to Speaker Amplifiers. 

1.  Volume control turned up (clockwise). 

 
 

2.  Check presence and polarity of -24VDC and GND. 

 
 

3.  Check audio presence and level on T-OUT and R-OUT at PRM-150, 

and if necessary also at the Speaker Amplifiers. 

 
 

4.  Check audio presence and level on T-IN and R-IN at PRM-150, and if 

necessary at the audio source. 

 
 

5.  Defective unit - Replace. 

 
 

ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER 
DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR 
ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION 
AND TESTING IS USED AT THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY LIABILITY 
FOR SUCH USE. 

 

Summary of Contents for PRM-150






Reviews: