background image

WARNING: DO NOT

unscrew the rear section as interference with the internal

electrics will render the pump unfit for use - this is a non-serviceable part of the pump.

NOTE:

Winterizing - Fully drain system

Whale® cannot guarantee warranty if the system is not fully drained for winterizing

For installation or service advice please contact Whale® customer support:

UK Tel: +44 (0)28 9127 0531 

USA Tel: 1 802 367 1091

UK Fax: +44 (0)28 9146 6421

USA Fax: 1 802 367 1095

UK Email: [email protected]  

Email USA: [email protected]

Trade marks - Whale® and Gulper ® are registered trademarks to Munster Simms

Engineering limited (also trading as Whale® Water Systems) 

Whale® Gulper® IC products are protected by the following patent applications: 

P92580GB00

P92043GB00

Failure to 

prime - Motor 

operates, but 

no pump 

discharge

Debris under flap valves 

/ not seated properly

Turn off  electrics and disconnect plumbing 

check valves for blockages and remove 

debris (See section 14) 

Air leak in intake line

Check hose connections are airtight. Open  

pump head and check valves and 

diaphragm (see section 14)

Punctured pump 

diaphragm

Replace the damaged part using service kit 

- Part number AK2050

Restricted intake or 

discharge line

Check all hose connections are airtight, 

free from blockages, and hose has not 

collapsed/kinked.

Pump fails to 

turn off when  

required

Strainer IC bilge strainer,   

not working

Check Strainer IC is operating properly 

(see section 13).

Defective/ debris on 

grey waste float switch

Clear debris/ replace float switch. 

Insufficient voltage to 

the pump

Check power supply to pump.

Override switch activated

Turn off override switch

Low flow

Air leak at pump intake

Check the hose connections are airtight.

Debris inside pump and 

plumbing

Turn off electrics and disconnect plumbing, 

check for blockages and remove (See  

section 14)

Punctured pump 

diaphragm

Replace the damaged part using service   

kit- Part number AK2050

Defective electronic 

control

Replace  pump. If within specified warranty 

period contact Whale (see contact details)

17. WINTERIZING 

18. SERVICE SUPPORT DETAILS

19. PATENTS AND TRADEMARKS

All manuals and user guides at all-guides.com

Summary of Contents for BP2083B














Reviews: