manualshive.com logo in svg

Wexiodisk WD-8, Installation And User Manual

Share
Download
Wexiodisk WD-8 Installation And User Manual Download Page 52

WD-8

 Rev. 4.0 (202202)

Operating instructions

48

Er16

The temperature in the booster heater is 
too low. 

The alarm can be reset by pressing 0/1 on the panel. 
Contact service personnel.

Low level in the break tank.

The alarm can be reset by pressing 0/1 on the panel. 
Contact service personnel.

Er23

The hood does not open when the 
automatic hood opener is used.

The alarm can be reset by pressing 0/1 on the panel. 
Contact service personnel if the fault recurs.

Er27

The machine has lost all its set values.

Contact service personnel.

IF30

Low water level in the washing tank 
before washing.

Check that the level pipe is closed. The alarm can be 
reset by pressing 0/1 on the panel.

The level pipe's rubber sleeve is leaking.

Check that the level pipe's rubber sleeve has not been 
damaged.

IF34

The detergent alarm.

The alarm can be reset by pressing 0/1 on the panel.

The machine has run out of detergent.

Check the amount of detergent and refill, if necessary.

IF35

The machine is started with the hood 
closed.

Open and close the hood to acknowledge the alarm.

Er96

The motor safety cut-out for the pump has 
tripped.

Contact service personnel.

Er97

One digital input is shorted to ground.

Contact service personnel.

Er98

Communication fault between the CPU 
and the panel card.

The alarm can be reset by pressing 0/1 on the panel. 
Contact service personnel if the alarm recurs.

Er99

Communication fault between the 
computer and panel cards.

The alarm can be reset by pressing 0/1 on the panel. 
Contact service personnel if the alarm recurs.

CODE

CAUSE

ACTION

Summary of Contents for WD-8

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands