Westweld NB-250LB Instruction Manual Download Page 5

 

 

 

 

Do not put your hand close to fans and do not move the brake handle while operating. 

 

Please remove the connection between the engine and the welding equipment to avoid sudden starting during 
maintenances. 

 

When engine is hot, it is forbidden to open the airtight cover of the radiator water tank to avoid hurt by the hot 
vapor. 

Electromagnetic

: Welding current going though any area can generate electromagnetic, as well 

as the welding equipment itself. 

 

Electromagnetic would affect cardiac pacemaker, the cardiac pacemaker users should consult 

one’s doctor first. 

 

The effect of electromagnetic to one’s health is not confirmed, and it might have some negative effect to one’s 
health. 

 

Welders may use following method to reduce the hazardous of electromagnetic: 

a. Bundle the cable connected to the work piece and the welding cable together. 
b. Do not enwind partially or entirely your body with the cable. 

c. Do not place yourself between the welding cable and the ground (work piece) cable, if the welding cable is by 

your left side, then the ground cable should be by your left side too. 

d. The Welding cable and the ground cable are as short as possible. 

e. D            e. Do not work near to the welding power source. 

Lifting equipment

: carton or wooden boxes package the welding machines supplied by 

Huayuan. There is no lifting equipment in its wrapper. Users can move it to the prospective area 
by a fork-lift truck, then open the box. 

 

If there are rings, the machine can be transited by rings. While Huayuan Welding Machine 
Manufacture reminds users, there is potential risk to damage the welding machine. So it is better 
to push the welding machine by its rollers unless special situations. 

 

Be sure that the appurtenances are all removed off when lifting. 

 

When lifting, make sure that there is no person below the welding machine, and remind people 
passing by at any moment. 

 

Do not move the hoist too fast.

 

10 

Noise

: Huayuan Welding Machine Manufacture reminds users: Noise beyond the limit (over 80 

db) can cause injury to vision, heart and audition depending on oneself. Please consult local 
medical institution. Use the equipment after doctor’s permission would help to keep healthy. 

                                             

 

                     

 

 

 

 

 

Summary of Contents for NB-250LB




















Reviews: