Westpow L1600, User Manual, Page: 13 / 21

8.2 Inquiry 8.2 Inquiry
8.2.2 Last Fault 8.2.2 Last Fault
8.2.1 Rate current 8.2.1 Rate current
Note:
1.User should select a suitable starting mode according the load.
2.To gain the better start effect, the ramp initial voltage shouldn't set too high.
30% to 50% of rated is recommend
3.Percent of the voltage is based on the electric net voltage the equipment connected.
4.Percent of the current is based on the rate current .
5.When the Starting mode parameter set 3, start/stop connect way is two-line (See
figure 5-2 on page 10), the key and key in disable.
Note:
1.User should select a suitable starting mode according the load.
2.To gain the better start effect, the ramp initial voltage shouldn't set too high.
30% to 50% of rated is recommend
3.Percent of the voltage is based on the electric net voltage the equipment connected.
4.Percent of the current is based on the rate current .
5.When the Starting mode parameter set 3, start/stop connect way is two-line (See
figure 5-2 on page 10), the key and key in disable.
User Manual User Manual User Manual User Manual
8. Parameter 8. Parameter
8.1 Function Display Range 8.1 Function Display Range
Functional Functional Name Name
Range and mean Range and mean
Default Default
Ready state Ready state
Starting mode Starting mode
Initial voltage Initial voltage
Ramp time Ramp time
Curr. Limit Level Curr. Limit Level
Curr. Limit time Curr. Limit time
Jogging Voltage Jogging Voltage
Control Mode Control Mode
Motor rate current Motor rate current
Fault Fault
1.Voltage ramp
2.Current limit
3.Jogging 1.Voltage ramp
2.Current limit
3.Jogging
30%~100% of Supply Voltage 30%~100% of Supply Voltage
1 120s 1 120s
100%~500% of rated current 100%~500% of rated current
1 120s 1 120s
30%~100% of Supply Voltage 30%~100% of Supply Voltage
0: Disable
1:Keyboard control
2: External control
3: Keyboard and external 0: Disable
1:Keyboard control
2: External control
3: Keyboard and external
Modify according the motor Modify according the motor
User can't modify User can't modify
1.Voltage ramp 1.Voltage ramp
30% 30%
20s 20s
300% 300%
30s 30s
30% 30%
3 3
Nameplate Nameplate
Table 8-1
User can't modify User can't modify
On state, press key and not release, code c and rate current
display on the keyboard , the unit is ampere. Release this key, system
return to state.
On state, press key and not release, code c and rate current
display on the keyboard , the unit is ampere. Release this key, system
return to state.
8.3 Setting 8.3 Setting
On Ready state , press key and release it 5 minutes later(or press
and )at the same time), system enter Setting state.
On Ready state , press key and release it 5 minutes later(or press
and )at the same time), system enter Setting state.
On state, press key and release it 5 minutes later, the last fault
code display on the keyboard . Release the key, then return state.
On state, press key and release it 5 minutes later, the last fault
code display on the keyboard . Release the key, then return state.
For example: the last fault is missing phase For example: the last fault is missing phase
Fault Fault
Figure8-2
Press Press
(maintain 5 seconds) (maintain 5 seconds) Release Release
For example: rate current is 150A For example: rate current is 150A
Rate current Rate current
Press Press
Figure8-1
Release Release
8.3.1 Starting mode 8.3.1 Starting mode
When entering the Setting state, the first parameter (Starting Mode Select)
shows on the keyboard panel. Then press or key to select
starting mode code. If 1 is selected, the lamp on the top-left of the
keyboard oltage amp is light, the Starting mode is Voltage Ramp.
If 2 is selected, the lamp on the top-left of the keyboard urrent
imit is light, the Starting mode is Current Limit. If 3 is selected,
the starting mode is Jogging. Any lamp on the left of keyboard is not light.
After the starting mode parameter is selected, press key, next
parameter at selected Starting mode can be modified. Press key,
system return Ready state.
When entering the Setting state, the first parameter (Starting Mode Select)
shows on the keyboard panel. Then press or key to select
starting mode code. If 1 is selected, the lamp on the top-left of the
keyboard oltage amp is light, the Starting mode is Voltage Ramp.
If 2 is selected, the lamp on the top-left of the keyboard urrent
imit is light, the Starting mode is Current Limit. If 3 is selected,
the starting mode is Jogging. Any lamp on the left of keyboard is not light.
After the starting mode parameter is selected, press key, next
parameter at selected Starting mode can be modified. Press key,
system return Ready state.
16
OPERATION
MENU
17
OPERATION
MENU