background image

TROUBLESHOOTING

ERROR CODE 

ERROR DESCRIPTION

CONTROL

F1 

Overfill

•  Power off your machine and close the tap�

• Contact the customer service centre�

F2 

Not draining�

•  Water discharge hose is clogged�

• The filters of your machine might be clogged�

•  Power off-on your machine and activate the 

program cancellation command�

•  If the error continues, contact the Customer 

Care Centre�

F3 

Inlet valve faulty

• Close the tap�

• Contact the Customer Care Centre�

F5

Inadequate water supply

•  Make sure the water tap is fully open and that 

there is mains water available�

•  Close the water tap, disconnect the hose from 

the tap and clean the filter at the connection 

end of the hose�

•  Restart your machine, contact the service if the 

error resumes�

F6 

Faulty heater sensor

Contact the Customer Care Centre�

F7 

Over temperature

Contact the Customer Care Centre�

F8 

Heating error

Contact the Customer Care Centre� 

F9 

Divertor valve faulty

Contact the Customer Care Centre�

FE 

Power supply problem

Contact the Customer Care Centre�

22

TROUBLESHOOTING

This document sets out the terms and conditions of the product 

warranties for Electrolux Appliances. It is an important document.  

Please keep it with your proof of purchase documents in a safe place 

for future reference should you require service for your Appliance.

1.  In this warranty:
 

(a)  

‘acceptable quality’ as referred to in clause 10 of this warranty has  

the same meaning referred to in the ACL;

 

(b)  

‘ACL’ means Schedule 2 of the Competition and Consumer Act 2010;

 

(c)  

‘Appliance’ means any Electrolux product purchased by you and 

accompanied by this document; 

 

(d)  ‘ASC’ means Electrolux authorised service centres;

 

(e)  

‘Electrolux’ means Electrolux Home Products Pty Ltd of 163 

O’Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in  

respect of Appliances purchased in Australia and Electrolux (NZ) 

Limited (collectively ‘Electrolux’) of 3-5 Niall Burgess Road, Mount 

Wellington, in respect of Appliances purchased in New Zealand; 

 

(f)  

‘major failure’ as referred to in clause 10 of this warranty has the  

same meaning referred to in the ACL and includes a situation when  

an Appliance cannot be repaired or it is uneconomic for Electrolux,  

at its discretion, to repair an Appliance during the Warranty Period;

 

(g)  ‘Warranty Period’ means the Appliance is warranted against  

  manufacturing defects in Australia for 24 months and in New Zealand  

  for 24 months, following the date of original purchase of the Appliance;
 

(h)  

‘you’ means the purchaser of the Appliance not having purchased the 

Appliance for re-sale, and ‘your’ has a corresponding meaning.

2.  

This warranty only applies to Appliances purchased and used in Australia 

or New Zealand and used in normal domestic applications and is in 

addition to (and does not exclude, restrict, or modify in any way) any  

non-excludable statutory warranties in Australia or New Zealand.

3.  

During the Warranty Period Electrolux or its ASC will, at no extra charge 

if your Appliance is readily accessible for service, without special 

equipment and subject to these terms and conditions, repair or replace 

any parts which it considers to be defective. Electrolux or its ASC may use 

remanufactured parts to repair your Appliance. You agree that any replaced 

Appliances or parts become the property of Electrolux. This warranty does 

not apply to light globes, batteries, filters or similar perishable parts.

4.  

Parts and Appliances not supplied by Electrolux are not covered by  

this warranty.

5.  

To the extent permitted by law, you will bear the cost of transportation, 

travel and delivery of the Appliance to and from Electrolux or its ASC. If you 

reside outside of the service area, you will bear the cost of:

 

(a)  travel of an authorised representative; 

 

(b)  

transportation and delivery of the Appliance to and from Electrolux or 

its ASC.

  

In all instances, unless the Appliance is transported by Electrolux or an 

Electrolux authorised representative, the Appliance is transported at the 

owner’s cost and risk while in transit to and from Electrolux or its ASC.

6.  

Proof of purchase is required before you can make a claim under  

this warranty. 

7.  

You may not make a claim under this warranty unless the defect claimed is 

due to faulty or defective parts or workmanship. Electrolux is not liable in 

the following situations (which are not exhaustive):

 

(a)  the Appliance is damaged by:

  (i)  accident
  (ii)  misuse or abuse, including failure to properly maintain or service
  (iii)  normal wear and tear
  (iv)  

power surges, electrical storm damage or incorrect power supply

  (v)  incomplete or improper installation
  (vi)  incorrect, improper or inappropriate operation
  (vii)  insect or vermin infestation
  (viii)  failure to comply with any additional instructions supplied with the 

Appliance;

 

(b)  the Appliance is modified without authority from Electrolux in writing;

 

(c)  

the Appliance’s serial number or warranty seal has been removed 

or defaced;

 

(d)  

the Appliance was serviced or repaired by anyone other than 

Electrolux, an authorised repairer or ASC.

8.  

This warranty, the contract to which it relates and the relationship between 

you and Electrolux are governed by the law applicable where the Appliance 

was purchased. Where the Appliance was purchased in New Zealand for 

commercial purposes the Consumer Guarantee Act does not apply.

9.  

To the extent permitted by law and subject to your non-excludable statutory 

rights and warranties, Electrolux excludes all warranties and liabilities 

(other than as contained in this document) including liability for any loss or 

damage whether direct or indirect arising from your purchase, use or non 

use of the Appliance.

10.    For Appliances and services provided by Electrolux in Australia, the 

Appliances come with a guarantee by Electrolux that cannot be excluded 

under the ACL. You are entitled to a replacement or refund for a major 

failure and for compensation for any other reasonably foreseeable loss or 

damage. You are also entitled to have the Appliance repaired or replaced if 

the Appliance fails to be of acceptable quality and  

the failure does not amount to a major failure. The benefits to you given by 

this warranty are in addition to your other rights and remedies under a law 

in relation to the Appliances or services to which the warranty relates.

11.  At all times during the Warranty Period, Electrolux shall, at its discretion, 

determine whether repair, replacement or refund will apply if an Appliance 

has a valid warranty claim applicable to it.

12.  For Appliances and services provided by Electrolux in New Zealand, the 

Appliances come with a guarantee by Electrolux pursuant to the provisions 

of the Consumer Guarantees Act, the Sale of Goods Act and the Fair 

Trading Act. 

13.  To enquire about claiming under this warranty, please follow these steps: 
  

(a)  

carefully check the operating instructions, user manual and the terms 

of this warranty; 

 

(b)  have the model and serial number of the Appliance available; 

 

(c)  have the proof of purchase (e.g. an invoice) available; 

 

(d)  telephone the numbers shown below. 

14.  You accept that if you make a warranty claim, Electrolux and its ASC may 

exchange information in relation to you to enable Electrolux to meet its 

obligations under this warranty. 

 Warranty

FOR SALES IN AUSTRALIA AND NEW ZEALAND

APPLIANCE: DISHWASHER

Important Notice

Before calling for service, please ensure that the steps listed in clause 13 above have been followed.

FOR SERVICE 

or to find the address of your nearest 

state service centre in Australia 

PLEASE CALL 13 13 49 

For the cost of a local call (Australia only)

SERVICE AUSTRALIA 

ELECTROLUX HOME PRODUCTS

electrolux.com.au

FOR SPARE PARTS 

or to find the address of your nearest 

state spare parts centre in Australia 

PLEASE CALL 13 13 50 

For the cost of a local call (Australia only)

FOR SERVICE 

or to find the address of your nearest 

authorised service centre in New Zealand 

FREE CALL 0800 10 66 10 

(New Zealand only)

SERVICE NEW ZEALAND 

ELECTROLUX (NZ) Limited

electrolux.co.nz

FOR SPARE PARTS 

or to find the address of your nearest 

state spare parts centre in New Zealand 

FREE CALL 0800 10 66 20 

(New Zealand only)

GDW_Warr_Sep15

Summary of Contents for WSF6725I

























Reviews: