manualshive.com logo in svg

Westinghouse WSF6606, User Manual, Page: 23 / 52

Share
Download
Westinghouse WSF6606 User Manual Download Page 23

23

MAINTENANCE AND CLEANING

MAINTENANCE

FAILURE CODES AND WHAT TO DO IN CASE OF FAILURE

PRACTICAL AND USEFUL INFORMATION

1  Whenever you will not be operating your machine:

•   

Unplug the machine and then turn the water 

off . 

•  Leave the door slightly ajar in order to prevent 

the formation of unpleasant odours . 

•  Keep the machine interior clean .

2  Eliminating water droplets:

•  Wash the dishes with the intensive program . 

•  Increase the rinse aid setting . 

•  If plastic items are washed, water drops on these 

items will be unavoidable . Programs with higher 

temperatures and increased rinse aid settings 

may reduce the water drops . Check that the 

plastic items are suitable for dishwasher use .

3  Correctly loaded dishes will give the best energy 

consumption, washing and drying performance .

4  Scrape off food soils before you place dirty dishes  

in the machine .

5  Operate the machine after it is completely full .

6   Use pre-washing program only when necessary .

7  Observe program information and average 

consumption values table when selecting a 

program .

8  Since the machine will reach high temperatures, 

it should not be installed near a refrigerator .

9   If the appliance is located where the risk of freezing 

exists, you must completely drain the water that 

has remained in the machine . Turn off the water tap, 

disconnect the water inlet hose from the tap and 

allow the interior water to drain .

F1

Leak detection

•  Switch off the dishwasher and close the tap .
•  Contact the service centre .

F2

Draining fault

•  Cancel program and power off machine, then check the following .
•  Spigot on sink trap is clogged .
•  Check if the drain spigot membrane has been removed .
•  Drain hose is clogged .
•  Filters of the dishwasher may be clogged .
•  If error continues contact the service centre .

F3

Water overfill

•  Close the tap .
•  Contact the service centre .

F5

Water supply fault

•  Make sur e the water tap is open and the main water supply is on .
•  Close he tap, disconnect the hose and clean the filter at the tap 

connection end .

•  Check the inlet hose is not kinked .
•  If error continues contact the service centre .

F6

Faulty heater sensor

•  Contact the service centre .

F7

Overheating (water temperature too high)

•  Contact the service centre .

F8

Not heating

•  Contact the service centre .

F9

Flow control position error

•  Contact the service centre .

FE

Power supply fault

•  Restart the dishwasher .

H01 – H24

Delay  has been selected

•  Cancel the delay setting .

Summary of Contents for WSF6606





















































Reviews:

No comments