background image

This is not a do-it-yourself project. Failure to have this appliance installed by a licensed plumber 

and electrician will void all warranties.

Under no circumstances should you attempt to install, repair or disassemble the electric 

instantaneous water heater without first shutting off all power to the unit directly at the circuit 

breaker box.

Installation of this product is restricted to indoor locations only by licensed plumbing or 

electrical contractors.

1. The installation must be in compliance with your local electrical and plumbing codes.

2. This appliance must be EARTHED.

3. All wiring and installation must be supervised by a qualified electrician.

4. This appliance is not intended for use by persons (include children) with reduced physical 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their safety. Children should be supervised to ensure that they do not play with the appliance.

5. This appliance MUST be permanently connected to the fixed circuit breaker and it must be 

installed vertically. DO NOT install this appliance near to tinder or strong magnetic field place.

6. This appliance is forbidden to be switched on if you think it may be frozen, as this could 

result in serious damage to the unit. Wait until you are sure that it has completely thawed out 

before you switch it on.

7. Please feel the outlet hot water temperature with hand to make sure it is suitable for 

showering before taking shower to avoid getting scalded.

8. Before connecting pipes to the water heater hoses, it is extremely important to FLUSH the 

pipes to wash away all plumbing paste or residue in the pipes.

9. If there is damage to the wire, you must contact qualified electrician to replace it with 

dedicated wire from our authorized dealers.

10. Check valve is required to be installed at the water inlet.

11. The water relief valve should work periodically in order to remove calcium carbonate 

deposits.

12. The drain-pipe which connected to the water relief valve should be installed continuous 

downward in frostless environment. 

13. The spray head must be descaled regularly  

14. The appliance could be fitted with a pressure relief device or valve at the water outlet during 

installation.

WARNING: Do not switch on if there is a possibility that the water in the heater is frozen.

Important Safety Instructions

Attention!

Summary of Contents for HT382E55













Reviews: