1
1
BULL BAR ASSEMBLY
2,3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
PLASTIC PLUG
5
4
RUBBER BUMPER
6
4
J-BOLT
7
2
1/2-13 X 2.00” HEX HEAD BOLT
8
2
1/2” FLAT WASHER
9
2
1/2” LOCK WASHER
10
4
3/8” FLAT WASHER
11
4
3/8” LOCK WASHER
12
4
3/8-16 HEX NUT
13
4
PLASTIC WASHERS
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
4
PERNOS EN “J”
7
2
PIEZA DE SUJECIÓN, LADO DEL ACOMPAÑANTE
Y EL CONDUCTOR
(2)
(3)
1/2-13 X 2.00”
8
2
ARANDELAS DE PRESIÓN DE
4
4
ARANDELAS DE PRESIÓN DE 3/8”
12
4
TUERCAS HEXAGONALES DE 3/8-16
13
4
ARANDELA DE PLÁSTICO
PERNOS CON CABEZA HEXAGONAL DE
ARANDELA PLANA SAE DE 1/2”
9
2
1/2”
10
ARANDELA PLANA SAE DE 3/8”
11
1
1
BARRE PARE-CHOCS SAFARI
2,3
2
SUPPORT CÔTÉ PASSAGER (2) ET CÔTÉ CONDUCTEUR (3)
4
2
BOUCHON DE PLASTIQUE
5
4
PARE-CHOCS EN CAOUTCHOUC
6
4
BOULON EN J
7
2
1/2-13 X 2.00
RONDELLE A FREIN 1/2 PO
10
4
4
RONDELLE A FREIN 3/8 PO
12
4
ÉCROU HEXAGONAL 3/8-16
13
4
RONDELLE DE PLASTIQUE
BOULON A TETE HEXAGONALE
PO
8
2
RONDELLE PLATE SAE 1/2 PO
9
2
RONDELLE PLATE SAE 3/8 PO
11
QTY
CONTENTS -
CONTENIDO
- CONTENU
TOOLS -
HERRAMIENTA
- OUTILS
3/4’’ SOCKET
9/16” SOCKET
9/16” WRENCH
RATCHET
SOCKET EXTENSION
TORQUE WRENCH
FLAT TIP SCREWDRIVER
APPLICATION: 2006-UP FORD EXPLORER
2007-UP FORD EXPLORER SPORT TRAC
ITEM
APLICACIÓN: FORD EXPLORER, 2006 Y SUPERIOR
FORD EXPLORER SPORT TRAC, 2007 Y SUPERIOR
APPLICATION: FORD EXPLORER 2006 ET PLUS
FORD EXPLORER SPORT TRAC 2007 ET PLUS
AUTOMOTIVE PRODUCTS, INC.
DADO DE 3/4´´
DADO DE 9/16
LLAVE DE TUERCAS DE 9/16”
DESTORNILLADOR DE PUNTA PLANA
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
”
DOUILLE 3/4 PO
DOUILLE 9/16 PO
CLE 9/16 PO
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
TOURNEVIS A POINTE PLATE
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
BARRE PARE-CHOC SAFARI
33-2030
33-2035
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
75-0615 REVISION A 2/9/07
STEP 1.
STEP 2.
STEP 3.
STEP 4.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
completely before beginning.
It will be necessary to remove the front license plate and bracket. Remove license plate from bracket.
Using a 3/16” drill bit, drill out the two pop rivets that hold the bracket to the bumper. If local/state laws
requires a license plate, license plate relocation kit 32-0055 is available.
Install brackets as shown in Figure 2.
Adjustment to the lower splash shield may be required. Minor
trimming of the air dam is required.
Attach Bull Bar to mount brackets using 1/2” fasteners. Level and adjust Bull Bar as desired and tighten all
fasteners. Recommended torque values are 26 FT.LBS. for 3/8” fasteners and 64 FT.LBS. for 1/2” fasteners.
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube. Thread
nut and washers on stud and tighten.
A short socket, not a deep well works best
to get the nut started.
NOTE:
NOTE:
LIGHT INSTALLATION:
SEE FIGURE 1. NOTE:
WO:
3
2
6
