3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service (800) 793-7846
www.westinautomotive.com
P.N.: 75-1008-RevC
ECO #: W15-0151
DATE: 9/10/15
5. Select the driver side front Mounting Bracket. Position the Mounting Bracket onto the front M10 Bolt Plate. Attach the
Bracket to the Bolt Plate with (1) M10 Flat Washer, (1) M10 Lock Washer, and (1) M10 Hex Nut,
(Fig. 6)
. Do not tighten
at this time.
Driver side up to mid 2015 without factory threaded inserts:
a.
Rotate the M12 Bolt and Nut plate until the threaded nut lines up with the remaining hole in the Mounting Bracket
and body,
(Fig. 5B)
. Attach the Bracket to the threaded Nut Plate with (1) M10 Hex Bolt, (1) M10 Lock Washer, and
(1) M10 Flat Washer,
(Fig. 6)
.
Driver side mid 2015-on with factory threaded inserts:
a.
Attach the Brackets to the threaded insert with (1) Long M8 Hex Bolt, (1) M8 Lock Washer, and (1) Large M8 Flat
Washer instead of the M10 hardware,
(Fig.7)
. Do not tighten hardware at this time.
Passenger side all model years:
a.
Repeat the previous applicable driver side instructions to attach the bottom/rear mounting hole on the passenger side
front Bracket to the Bolt/Nut plate or threaded insert if equipped,
(Fig.6 & 7)
. Do not tighten hardware at this time.
6. Remove the driver side front factory body bolt and washer. Select the driver side Front Support Bracket. Insert the factory
body bolt and washer through the slot in the Support Bracket and up into its original position,
(Fig. 8 & 9)
. Line up the
other end of the Support Bracket with the oval hole in the Front Mounting Bracket. Snug but do not tighten hardware.
7. Move to the mid point on the driver side of the vehicle and remove the tape covering the factory oval hole in the inner
body panel,
(Fig. 10B)
. Select and install a M12 Bolt and Nut Plate with M12 Plastic Retainer as described in
Step 3
,
(Fig. 10A & 10B)
.
8. Select the driver side Center Mounting Bracket. Attach the Mounting Bracket to the Bolt and Nut Plate with (1) M12 Flat
Washer, (1) M12 Lock Washer and (1) M12 Hex Nut,
(Fig. 11)
. Rotate the Bolt and Nut plate until the Nut end lines up
with the remaining hole in the Mounting Bracket and body. Thread (1) M10 Hex Bolt, (1) M10 Flat Washer, and (1) M10
Lock Washer into the threaded nut.
On models with factory installed threaded insert
, use the Bolt and Nut Plate to at-
tach the top of the Bracket but attach the bottom of the Bracket to the threaded insert with (1) Long M8 Hex Bolt, (1) M8
Lock Washer and (1) Large M8 Flat Washer instead of the M10 hardware,
(Fig. 11)
. Do not tighten hardware at this time.
9. Next, move to the rear mounting location and remove the tape covering the single factory hole,
(Fig. 12B)
. Select (1) M12
Bolt Plate and M12 Plastic Retainer,
(Fig. 12A)
. Partially thread the Retainer onto the Bolt Plate. Insert the Bolt Plate into
the factory oval hole. Select (1) Rear Mounting Bracket. Attach the Bracket to the Bolt Plate with (1) M12 Flat Washer, (1)
M12 Lock Washer, and (1) M12 Hex Nut. Push Bracket up against the body as you tighten the hardware,
(Fig. 13)
.
10. Remove the driver side rear factory body bolt and washer. Select the driver side Rear Support Mounting Bracket,
(Fig. 14)
.
Insert the factory body bolt and washer through the Support Mounting Bracket and up into its original position. Next, se-
lect (1) Rear Support Strap and bolt it to the mounting tab on the Rear Support Mounting Bracket and to the Rear Mount-
ing Bracket with (2) M10 Hex Bolts, (4) Small M10 Flat Washers, (2) M10 Lock Washers and (2) M10 Hex Nuts,
(Fig.
15)
. Snug but do not tighten hardware at this time.
11. Select the driver Side Step Bar and with assistance, carefully fasten it to the front and rear Mounting Brackets with the in-
cluded (2) 1/2” Hex Head Bolts, (2) 1/2” Lock Washers, and (2) 1/2” Flat Washers,
(Fig. 15 & 16)
. Do not tighten at this
time.
12. Level and align Side Step Bar properly; then snug all hardware on the front and rear Mounting Brackets first.
13. Line up the Center Mounting Bracket with the threaded insert in the Side Step Bar. Insert (1) Short M8 Hex Bolt, (1) M8
Lock Washer, and (1) M8 STD Flat Washer through the Center Bracket and into the threaded insert in the Sidebar,
(Fig.
17)
. Slowly tighten the Mounting Hardware.
14. Check the Side Step Bars for level and adjust as necessary. Tighten all hardware at this time.
