manualshive.com logo in svg

Western Aertesi Brezza Series, Installation, Operation And Maintenance Manual

Share
Download
Western Aertesi Brezza Series Installation, Operation And Maintenance Manual Download Page 23

 

 

23

Before  installing  electricity,  see  specific  circuit  diagram  of  the  unit  supplied  with  the  unit.  After  completing  the 

electrical installation, replace the electrical panel cover and secure it with the two screws. 

12-MAINTENANCE 

The maintenance of the unit can only be done by qualified and trained. 

Before performing any maintenance on the unit, make sure that the main power supply is switched off and that it 

cannot be accidentally inserted. Make sure the motor is stopped before opening the cassette cover. 

The  motor,  the  coil  and  the  drainage  pump  does  not  require  regular  maintenance.  The  filter  instead  requires 

periodic cleaning. 

 

12.1-Filter 

The  filter  must  be  cleaned  periodically,  every  6  months  or  more  often  if  the  environment  is  dusty.  It  can  be 

cleaned  with  a  vacuum  cleaner  or  slightly  beaten.  To  access  the  filter  pull  down  gently  on  the  front  panel  to 

release the magnet fixing. 

Pull only in the two corners (maximum 5cm from the edge) at the two labels " PULL ". 

 

 

 

PULL LABEL ON PANEL 

 

 

 

Summary of Contents for Aertesi Brezza Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands