manualshive.com logo in svg

Western Digital WD 1003-RA2, User Manual

Share
Download
Western Digital WD 1003-RA2 User Manual Download Page 7

WD1003-RA2: Attach drive 0's 20-pin data connector to J4.

WD1003A-RA2: Attach drive 0's 20-pin data connector to J3.

7.

WD1003-RAH
WD1003S-RAH
WD1003-RA2: Attach drive 1's data connector to J3.
WD1003A-RA2: Attach drive l's data connector to J2.

8.

Connect data cables to drives.

9.

WD1003-RA2: Attach 34-pin floppy cable connector to J1.
WD1003A-RA2: Attach 34-pin floppy cable connector to J5.

10. WD1003-RAH

WD1003S-RAH
WD1003-RA2: Attach Winchester activity LED connector to J6.
WD1003A-RA2: Attach Winchester activity LED to Jl.

11.

Install the controller board into the expansion slot. Make sure that the board is seated
properly by pressing down on both ends of the board. Secure the board with the bracket
screw.

12.

Remove or disable any other floppy controller in your system if you are installing a
WD1003RA2 or WDl003A-RA2. It is NOT possible to disable the floppy controller on
the WD1003-RA2 or WD 1003A-RA2.

Summary of Contents for WD 1003-RA2















Reviews:

No comments

Brands by name

Popular brands

Load more brands