background image

 

WRD

 

Manuale utente

 

 

EN

 

 

8. CONFIGURATIONS 

 

8.1. Configuration: WRD + WBM 

8.1.1. Description 

This configuration is used in a plant where you want to monitor the energy flow of the

 battery 

(

Pic.

 A1). The WBM 

battery  monitor  must  be  connected  to  the  negative  battery  terminal  and  provides  for  the  calculation  of  the 
incoming and outgoing energy. (See dedicated product manual for more details). 
WRD allows configuring the WBM in the Setup menu 7.0 or 8.1: 

x

 

Select the correct profile according to the type of battery. 

x

 

Select the battery capacity (Ah) correctly, so that the WBM can correctly calculate the State of Charge (%) 
of the Battery. 

x

 

Set the thresholds for the two contacts controlled according to the State of Charge (%) of the Battery. 

The 'Discharge' contact can be exploited to control a device capable of disabling the load, thus determining the 
maximum discharge depth within which the battery will cycle. This contact also intervenes in case of protections: 
overcurrent, over temperature and under voltage. 
With the 'Charge' contact, normally, is controlled a device capable of disabling the charge as it intervenes in the 
event of protections: overcurrent, over temperature and overvoltage. 
Setting  the  thresholds  for  the  'Charge'  contact  it  can  also  be  controlled  according  to  the  SoC  in  case  some 
applications require it. 
 

8.1.2. Main screens 

In the following picture are described the graphic used in the various screens of the main menu. 
Take into account the notes shown in the pictures. 

 
 

8.2. Configuration: WRD + WRMxx

 (1 ..8) 

8.2.1. Description 

This  configuration  is  used  in  a  stand-alone  system  where  you  want  to  mainly  monitor  the  energy  production 
(

Pic.A2

). 

The  WRMxx  controllers,  which  can  be  paralleled  up  to  a  maximum  of  8,  are  used  to  charge  the  battery.  (see 
dedicated product manual for more details). 
The WRD allows to collectively  configuring  the most common parameters of all the WRMxx in the  Setup Menu 
7.0, while it performs this individually in the Setup Menu 8.2.: 

x

 

Select the correct profile according to the type of battery. 

x

 

Select appropriately the setting of the Load output 

x

 

Set the Low Battery threshold for the output Load. 

 
 - With the WRM30+: Load output can be exploited with setting 'SurPlus' to control or directly feed a load when 
the battery is charged and there is still energy from the PV modules so we have an excess of energy that in this 
way can be re-used. 
 

8.2.2. Main screens 

In the following picture are described the graphic used in the various screens of the main menu. 
Take into account the notes shown in the pictures. 

 

 

Summary of Contents for WRD


































Reviews: