background image

5

6650-2223

Declaration of Conformity

 
 

Westermo Teleindustri AB 

 

 

Declaration of conformity

 

 

Org.nr/

Postadress/Postal address

 

Tel.

 

Telefax

 

Postgiro

 

Bankgiro

 

Corp. identity number

 

Registered office 

S-640 40  Stora Sundby 

016-428000 

016-428001 

52 72 79-4 

5671-5550 

556361-2604 

Eskilstuna 

Sweden 

Int+46 16428000 

Int+46 16428001 

 

 

 

 

 

 
 

The manufacturer

 

Westermo Teleindustri AB 

 

SE-640 40 Stora Sundby, Sweden 

 

Herewith declares that the product(s) 

Type of product 

Model 

Art no 

Industrial fiberoptic repeaters/media 
converters 

ODW-600 Series 
 

3650-0xxx 
 

 

is in conformity with the following EC directive(s). 
No Short 

name 

 

2004/108/EC Electromagnetic 

Compatibility 

(EMC) 

 

References of standards applied for this EC declaration of conformity. 
No Title 

 

Issue 

EN 50121-4 

Railway applications – Electromagnetic compatibility 
– Emission and immunity of the signalling and 
telecommunications apparatus 

2006 

EN 55022 

Information technology equipment - Emission 

2006 +A1:2007 

EN 55024 

Information technology equipment - Immunity 

1998 +A1:2001 
+A2:2003 

EN 61000-6-1 

Electromagnetic compatibility – Immunity for 
residential environments 

2007 

EN 61000-6-2 

Electromagnetic compatibility – Immunity for 
industrial environments 

2005 

EN 61000-6-3 

Electromagnetic compatibility – Emission for 
residential environments 

2007 

EN 61000-6-4 

Electromagnetic compatibility – Emission for 
industrial environments 

2007 

The last two digits of the year in which the CE marking was affixed: 

09 

 

 

Pierre Öberg 
Technical Manager 
29th September 2009 

 

Summary of Contents for ODW-621





















Reviews: