background image

However, there is no guarantee that interference will not occur in a particular installation.
If this product does cause harmful interference to radio or television reception, which can
be determined by turning the product off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the unit and receiver
• Connect the product into an outlet on a circuit different from that to which the receiver

is connected

• Consult the dealer or an experienced radio/TV technician for help

NOTE
This product contains FCC ID 2AEJD-103902-DT50RF.

2.5.3. United States - AREMA
The product has been tested according to AREMA Part 11.5.1 environmental class B and
AREMA Part 11.5.2 exposure class External.

2.5.4. Canada - IC
This product complies with Industry Canada’s license-exempt RSSs. Operation is subject to
the following two conditions:

• This product may not cause interference.
• This product must accept any interference, including interference that may cause

undesired operation of the product.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

• l’appareil ne doit pas produire de brouillage.
• l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

NOTE
This product contains the IC Certification number 9301A-103902DT50.

10

Ibex-RT-370 Series

Summary of Contents for 3623-077001

































Reviews: