background image

WARNING - RADIO PRODUCTS
Observe the usage limitations of radio products at filling stations, in
chemical plants, in systems with explosives or potentially explosive
locations.

The product may not be used in airplanes. Exercise particular caution near
personal medical aids, such as pacemakers and hearing aids. Never
perform work on the antenna system during a thunderstorm.

To fulfill human safety, a minimum separation distance of 20 cm or more
should be maintained between the antenna of the product and personnel
during operation.

CAUTION - HOT SURFACE
Be aware that the surface of this product may become hot. When it is
operated at high temperatures, the external surface may exceed Touch
Temperature Limit according to the product's relevant electrical safety
standard.

This product complies with Touch Temperature Limits throughout its
operational temperature range.

CAUTION - CORROSIVE GASES
If the product is placed in a corrosive environment, it is important that all
unused connector sockets are protected with a suitable plug, in order to
avoid corrosion attacks on the gold plated connector pins.

CAUTION - CABLE TEMPERATURE RATING FOR FIELD
TERMINAL WIRES
There may be a requirement on the minimum temperature rating of the
cable to be connected to the field wiring terminals, see Interface
Specifications.

2.3. Care Recommendations

Follow the care recommendations below to maintain full operation of the product and to
fulfill the warranty obligations:

6

Ibex-RT-220 Series

Summary of Contents for 3623-072201































Reviews: