Section BXM‐161‐4HE‐20A
030‐101374 Rev. A
R
8
1211IARA
A.
Read and understand all instructions.
B.
Follow all warnings and instructions marked on product.
C.
Do not place this product on an unstable cart, stand or table:
the product may fall, causing serious damage to product.
D.
Slots and openings in the cabinet are provided for ventilation.
To protect it from overheating, these openings must not be
blocked or covered. This product should never be placed near
or over a radiator or heat register. This product should not be
placed in a built‐in installation unless proper ventilation is pro
vided.
E.
This product should be operated only from the type of power
source indicated on the marking label.
F.
Never push objects of any kind into this product through cabi
net slots as they may touch dangerous voltage points or short
out parts that could result in the risk of fire or electrical shock.
Never spill liquids of any kind on the product.
CAUTION ‐ STATIC‐SENSITIVE
This product contains static‐sensitive components! Proper
electrostatic discharge procedures must be followed to
maintain personal and equipment safety. Do not store units
near magnetic, electromagnetic or electrostatic fields. Always
store or ship units in the original static‐protective packaging
from Westell. Use anti‐static mats when working on units.
‐ PRECAUTIONARY STATEMENT ‐
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack
is specifically designed for wet locations.
Never touch uninsulated telephone wires or terminals unless
the telephone line has been disconnected at the network
interface.
Use caution when installing or modifying telephone lines.
3.3
Selecting and Preparing the Mounting Type
and Site
(Pre‐Mounting Considerations)
Mount the cabinet in a location with an adequate earth ground
and power access, with unobstructed cabinet access, and which
insures the best lighting, ventilation, heat dissipation, and equip
ment access. Verify sufficient space exists to allow the opening
of the left‐hinged large door, to access and mount the cabinet,
to mount and access the optional battery box if it will be mounted
below it, and to adequately access, prepare, and dress all cables.
Adequate horizontal and vertical space should be be left be
tween any multiple installations to allow for cabinet opening,
equipment access, and cable routings and preparations. Follow
company practice for the proper distance from the cable entry
point or from upstream or downstream equipment.
3.4
Gathering all Tools and Equipment
The following tools and supplies (not provided) are required to
mount the Boxer‐16 cabinet.
Door Opening/Locking Tools
V
7/16” can wrench or 216 tool
V
Padlock (optional)
Knock‐Out Removal Tools
V
Hammer
V
Punch
V
Pliers
Cabinet Mounting Tools, Equipment, and Hardware
V
Tape measure
V
Marking utensil (to mark mounting hole locations)
V
Level (optional)
V
Power or hand drill with assorted bits, plus long bits or drill
bit extensions if pole mounting
V
Socket driver and sockets, or wrenches
V
Wall‐ or pole‐mounting hardware, such as 3/8” diameter
wood‐type lag screws or bolts
V
H‐frame mounting hardware (for H‐frame mounting)
V
Optional pole‐mount kit (for pole mounting)
V
Outdoor site preparation tools
V
Safety gloves and glasses (optional)
V
Power hoist or lifting equipment and cables (optional)
V
Assorted screwdrivers
V
Appropriate ground wire and equipment
Cable Preparation Tools and Equipment
V
Cable opening and preparation tools
V
Proper lengths and types of communications cables
V
Proper lengths and types of power cables and fittings
V
Cable management supplies (ties, clips, markers, etc.)
V
Power installation and testing equipment
V
ESD protection
3.5
Removing the Knock‐outs
Knock‐outs should be removed prior to mounting the cabinet.
See Figure 9 or Table 1 for knock‐out sizes, quantities, and loca
tions, and follow the steps below to remove the knock‐outs.
1.
Open the cabinet door.
If knock‐outs will need to be re
moved, using a 216 tool or can wrench, open the large front
door of the Boxer‐16 cabinet to access the knock‐outs.
2.
Remove knock‐out(s).
Prior to mounting the cabinet, per
company practice, remove as many appropriately‐sized
knock‐outs at the bottom of the cabinet as needed for the
specific application (consider ground, power, and com
munication cable access needs, venting, and whether
optionally mounting a battery box with the cabinet).
3.
Install rubber grommets or conduit fittings.
Install either
a heavy‐duty rubber grommet or the conduit fitting of
choice (liquid‐tight recommended) in each selected
knock‐out hole. If an optional vent is desired, the provided
vent cap can be installed in one of the smaller knock‐outs.
4.
Close the cabinet door.
Once the knock‐outs are removed,
lock the door using the 216 tool or can wrench, to minimize
possible product damage and personal injury.
3.6
Mounting the Cabinet
The Boxer‐16 cabinet is typically mounted outdoors, above
ground, on an H‐frame, a wall, post, a concrete pad, or a pole.
An optional mounting kit is available to support pole mounting
(from 8” to 20” in diameter). Concrete pad mounting is typically
used when used with an optional Boxer battery box or skirt. An
optional pad mount template kit is available for easy and conve
nient cement anchor placement. All mounting hardware (not
provided) must be capable of supporting the weight of the Box