Westeel WaterTank Flat Roof Installation And Storage Instructions Download Page 4

 

x.  any use or installation inconsistent with Westeel’s Standard Disclaimers. 

xi.  cosmetic changes such as white rust and scratches 

 
 
5. 

Limitations as to Manufacturer.

  The warranty does not cover products sold by 

Westeel that are not manufactured by Westeel.  In those circumstances, the 
purchaser is referred to the manufacturer of those products. 
 
 

6. 

Limitation of Implied Warranties and Other Remedies

.  To the extent allowed by 

law, neither Westeel nor its dealers, nor any company affiliated with Westeel makes 
any implied or other warranties, representations, or promises as to the quality, 
performance, or freedom from defect of any Product covered by this Warranty. 

 

 

WESTEEL HEREBY DISCLAIMS, TO THE EXTENT APPLICABLE, ANY AND 
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE. A PURCHASER’S ONLY REMEDIES IN CONNECTION 
WITH THIS WARRANTY ARE THOSE SET FORTH IN THIS WARRANTY.  IN NO 
EVENT WILL WESTEEL, ITS DEALERS, OR ANY COMPANY AFFILIATED WITH 
WESTEEL BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR PUNITIVE 
DAMAGES.

  

Some jurisdictions do not allow waivers of certain warranties, so the above waivers 
may not apply to you.  In that event, any implied warranties are limited in duration to 
ninety (90) days from delivery of the products. You may also have other rights which 
vary from jurisdiction to jurisdiction. 

 
 
7. 

Exclusive Warranty.

 This warranty is the only warranty provided by Westeel and all 

other warranties and/or commitments whether expressed or implied and no matter 
by whom made, statutory or otherwise, are subsumed and replaced by it and are of 
no legal effect.  If any provision of the warranty is held by a court of competent 
jurisdiction to be void or unenforceable, in whole or in part, such provision shall be 
deemed severable and will not affect or impair the legal validity of any other 
provision of the warranty. 

 

Page 4 

Summary of Contents for WaterTank Flat Roof
























Reviews: