West Mountain Radio PWRguard PLUS Operating Manual Download Page 3

3

West Mountain Radio

Operating Manual

Installation

1.  Install the PWRguard PLUS between the power source and the 

loads to be protected.

 

NOTE:  The unit comes fitted with Powerpole® connectors for ease 

of installation into your power system. 

Input (power source) connects on the left side of the case. 

Output (load) connects on the right side of the case.

 

Make sure that you only connect the RED lead to POSITIVE, and the 

BLACK lead to NEGATIVE.

2.  Install the unit in a cool dry location.  The case may be fastened 

down using the mounting holes on the flanges.

3.  The external sense terminal is located within the unit. Remove the 

case and locate the small terminal-block on the left hand side. The 

terminal nearest the edge of the board pr5VDC through a 

330 ohm resistor and the right terminal is the sense input.

 

The piezo buzzer alarm can be disabled by removing the jumper 

from the terminal post marked “Buzzer”.

4.   When the power supply is switched on, the PWRguard Plus unit will  

become operational and the AUTO RESET and ON LEDs will   

both glow green. If the AUTO RESET LED does not turn on, hold  

the reset button down for 5 seconds until it does. If the YELLOW 

LED (Low fault) comes on instead of the ON LED, it means that your 

power supply or battery voltage is too low. PWRguard Plus requires 

at least 13 (+/- 0.1) volts to become operational when turned on.  If 

supply voltage range is between 11-13V, you will need to manually 

turn on by pushing reset.

 

This setup integrates PWRguard Plus into a UPS. The PWRGuard 

Plus input is connected to the output of the Super PWRgate. The 

PWRguard Plus output is connected to the input of the RIGrunner. 

This setup will protect the battery from deep discharge after an AC 

power loss, and all devices that are plugged into the RIGrunner from 

under and over voltage. After AC power is restored, the battery will 

be recharged through the Super PWRgate and PWRguard Plus will 

reset the system. 

5V DC

Sense Input

Buzzer Jumper

USB Programming Connector

Summary of Contents for PWRguard PLUS











Reviews: