15
6
ATTACHING THE LEG LEVER TO THE LOW
PULLEY STATION
To use the Leg Lever (29), the seat must be attached
to the Front Upright (42) (see ATTACHING AND
REMOVING THE SEAT on page 14). Attach the Chain
(84) between the Short Cable (23) and the 5/16” x 2”
Eyebolt (35) on the Leg Lever with two Cable Clips
(83).
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE HIGH PULLEY STATION
Attach the Lat Bar (85) to the Long Cable (66) with a
Cable Clip (83). For some exercises, the Chain (84)
should be attached between the Lat Bar and the Long
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Long Cable so
the Lat Bar is in the correct starting position for
the exercise to be performed.
The Nylon Strap (39) can be attached in the same
manner.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE LOW PULLEY STATION
Attach the Lat Bar (85) to the Short Cable (23) with a
Cable Clip (83). For some exercises, the Chain (84)
should be attached between the Lat Bar and the Short
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Short Cable so
the Lat Bar is in the correct starting position for
the exercise to be performed.
The Nylon Strap (39) can be attached in the same
manner.
39
39
66
83
84
85
85
23
83
83
84
83
42
84
23
35
29
2.
Press the two 2” Outer Caps (88) onto the
Stabiliser (5).
Insert two 5/16” x 2 3/4” Carriage Bolts (14) up
through the Stabiliser (5). Slide the end of the Base
(4) onto the Carriage Bolts. Slide the Rear Upright
(82) onto the Carriage Bolts; make sure the sloped
bracket is oriented as shown. Thread two 5/16”
Nylon Locknuts (3) onto the Carriage Bolts. Do not
tighten the Nylon Locknuts yet.
Attach the ends of the Braces (86) with slotted
holes to the Stabiliser (5) with two 5/16” x 2 3/4”
Bolts (11), two 5/16” Flat Washers (8), and two
5/16” Nylon Locknuts (3). Do not tighten the Nylon
Locknuts yet.
Attach the other ends of the Braces (86) to the
Rear Upright (82) with a 5/16” x 2 3/4” Bolt (11), a
5/16” Flat Washer (8), and a 5/16” Jam Nut (2).
Do not tighten the Jam Nut yet.
3. Press the 1 1/4” Inner Cap (57) into the Front
Upright (42).
Attach the 1” Plastic Stop (64) to the centre hole in
the Stop Bracket (63) with a 5/16” x 1 1/2” Bolt (24)
and a 5/16” Jam Nut (2).
Attach the Stop Bracket (63) to the Front Upright
(42) with the 5/16” x 2” Bolt (61), a 5/16” Flat
Washer (8), and a 5/16” Nylon Locknut (3).
Slide the Front Upright (42) onto the two 5/16” x
2 1/2” Carriage Bolts (1) in the Base (4). Attach the
Front Upright to the Base with two 5/16” Nylon
Locknuts (3). Do not tighten the Nylon Locknuts
yet.
3
3
57
42
64
63
24
2
61
8
3
1
4
2
88
8
3
4
82
Low Side
3
8
14
88
5
11
86
3
8
2
11
Slot
Slot
