background image

4. Attach a Handrail Cover (63) and the Left Handrail (4)

to the left Upright (38) with two Handrail Knobs (1) and
two Knob Washers (13). Do not tighten the Handrail
Knobs yet. If you are shorter than 5’ 8”, use the
upper two holes in the Handrail; if you are 5’ 8” or
taller, use the lower two holes.

Have a second person hold the Console Base (87)
and the Right Handrail (32) in the position shown.
Feed the excess Wire Harness (53) into the upper end
of the Handrail, and pull the excess from the lower
end of the Handrail. Then, insert the excess Wire
Harness into the right Upright (38).  

Next, attach a Handrail Cover (63) and the Right
Handrail (32) to the right Upright (38) with two Handrail
Knobs (1) and two Knob Washers (13). Do not tight-
en the Handrail Knobs. Make sure that both
Handrails are at the same height.

Refer to the inset drawing. Insert a Handrail Plug (70)
into the unused hole in each Handrail (4, 32).

5. Set the Console Base (87) on the Handrails (4, 32).

Route the Wire Harness (53) as shown, and attach the
Console Base to the Handrails with the four Console
Screws (8). Make sure that the Handrail Screws are
tight, but do not overtighten them. 
Insert the excess
Wire Harness (53) into the Right Handrail. 

Tighten the four Handrail Knobs (1) used in step 4.

6. The Console (11) requires three "AA" batteries (not

included); alkaline batteries are recommended. Open
the Battery Cover (12) and press the batteries into the
Console; the negative (–) ends of the batteries must
touch the springs. Close the battery cover, push up on
the tab, and then push the tab forward as shown in the
inset drawing. Be sure that the tab locks into place.

7. Remove the backing from the Adhesive Clip (80).

Press the Adhesive Clip onto the right Upright (38).
Press the Allen Wrench (81) into the Adhesive Clip.

8. Make sure that all parts are properly tightened

before you use the treadmill. Some parts may be left
over after assembly is completed. To protect the floor
or carpet from damage, place a mat underneath the
treadmill. 

6

5

8

87

32

4

8

53

11

12

Batteries

Battery Cover Tab

7

81

38

80

70

4, 32

4

63

4

63

1

3

38

32

3

53

1

Ramps

6

13

13

87

53

Summary of Contents for Cadence 1020 Treadmill




















Reviews: