Wesco WS3441 Manual Download Page 19

19

EN

5. HAND GRIP POSITION (SEE FIG. E)

Always hold your saw firmly with both hands when 
operating.

6. SAFETY ON/OFF SWITCH (SEE FIG. F)

Your switch is locked off to prevent accidental starting. 
Depress the lock off button (17) then the on/off switch and 
release the lock off button. Your switch is now on. To switch 
off, just release the on/off switch. 
The blade may continue to rotate after switching off. Wait 
until the machine comes to a complete stop before setting 
down.

7. PARALLEL GUIDE ADJUSTMENT (SEE FIG. I)

It is used for making cuts parallel to a workpiece edge at a 
chosen distance. Slide the parallel guide arm through the 
fixture to achieve the required cutting distance then tighten 
the lock knob to clamp. It can be used from both sides of 
the base plate. For straight cuts, use the 0° guide mark to 
align with your parallel guide scale. For a 45° bevel cut, use 
the 45° guide mark to align with your parallel guide scale. 
Securely clamp the parallel guide.

Note:

 It is best to carry out a trial cut. 

WORKING HINTS FOR 

YOUR CIRCULAR SAW

If your power tool becomes too hot, run your circular saw 
no load for 2-3 minutes to cool the motor. Avoid prolonged 
usage at very low speeds.
Always use a blade suited to the material and material 
thickness to be cut. The quality of cut will improve as the 
number of blade teeth increase.
Always ensure the work-piece is firmly held or clamped to 
prevent movement. Support large panels close to the cut 
line. Any movement of the material may affect the quality 
of the cut. The blade cuts on the upward stroke and may 
chip the uppermost surface or edges of your work piece. 
When cutting, ensure your uppermost surface is a non-
visible surface when your work is finished. Feeding too fast 
significantly reduces the performance of the machine and 
shortens the life of the saw blade. Always face the good side 
of the work-piece down, to ensure minimum splintering. 
Only use sharp saw blades of the correct type.

MAINTENANCE

Remove the plug from the socket before 
carrying out any adjustment, servicing or 
maintenance.

Your power tool requires no additional lubrication or 
maintenance. There are no user serviceable parts in your 
power tool. Never use water or chemical cleaners to clean 
your power tool. Wipe clean with a dry cloth. Always store 
your power tool in a dry place. Keep the motor ventilation 
slots clean. Keep all working controls free of dust. 
Occasionally you may see sparks through the ventilation 
slots. This is normal and will not damage your power tool.  
If the supply cord is damaged, it must be replaced by 
the manufacturer, its service agent or similarly qualified 
persons in order to avoid a hazard. 

Summary of Contents for WS3441





















Reviews: