Wesco WS3441 Manual Download Page 18

18

EN

SYMBOLS

 

To reduce the risk of injury, user must 

 

read instruction manual

 

Double insulation

 

Warning

 

Wear ear protection

 

Wear eye protection

  Wear dust mask

OPERATION 

INSTRUTIONS

 

NOTE:

 

Before using the tool, read the 

instruction book carefully.

INTENDED USE

The machine is intended for lengthways and crossways 
cutting of wood with straight cutting lines as well as bevel 
angles to 45° while resting firmly on the work piece.

1. FITTING/CHANGING A SAW BLADE (SEE 
FIG. A1, A2, A3)

Press the spindle lock button and use the hex key to loosen 
and remove the blade bolt (11). Remove the outer flange 
(10). Rotate the lower blade guard clockwise by pushing 
the guard lever to take out the old blade (12). Fit a replaced 
blade. Ensure that the blade bore is located on the inner 
flange (a) and the blade direction arrow points in the same 
direction as the fixed guard arrow. Place the outer flange, 
the blade bolt onto the blade bore. Press the spindle lock 
again and use the hex key to tighten the bolt with 1/4 
turn more than finger tight. Check if the blade is securely 
clamped.

Warning: Blade teeth are very sharp.

 For 

best cutting results ensure you use a saw blade 

suited to the material and cut quality you need.

2. DEPTH OF CUT ADJUSTMENT (SEE FIG. B)

Lift the depth of cut lock lever and raise the saw body away 
from the base plate. Set the depth of cut with the scale and 
push the lever down to lock. Always add 3mm to your depth 
of cut so that the blade can cut through the material.

3. BASE PLATE ANGLE ADJUSTMENT (SEE 
FIG. C1, C2)

Turn the base plate bevel lock in anti-clockwise direction 
to loosen the angle scale. Tilt the base plate away from the 
machine until the required cutting angle is adjusted on the 
angle scale. Tighten the bevel lock by turning it in clockwise 
direction. Do not use the depth of cut scale when making 
bevel cuts due to possible inaccuracy.

4. DUST EXTRACTION OUTLET (SEE FIG. D)

Fasten the vacuum adapter (14) onto the dust extraction 
outlet until it latches. Additionally fasten the vacuum adapter 
(14) to the fixed guard with the two screws. Directly connect 
a suitable vacuum hose to the adapter.

Clean the vacuum adapter regularly to 
ensure optimum dust extraction. The 
vacuum cleaner must be suitable for the 
material to be worked

.

Summary of Contents for WS3441





















Reviews: