Wesco 272152 Instruction Manual Download Page 5

Page

 

5

 

of

 

14

 

 

© Copyright 2016 WESCO Industrial Products, Inc. Specifications subject to change. Not responsible for errors or omissions. 

  

 

3.  ADJUSTING RELEASE DEVICE (continued)

 

 

3.2 

If the forks descend while pumping in the 

DRIVE 

position, turn the Nut (104S) or 

Screw (318S) counter-clockwise until the forks do not lower. 

 

3.3 

If the forks do not descend when the Control Handle (117S) is in the 

LOWER 

position, 

turn the Nut (104S) or Screw (318S) clockwise until raising the Control Handle 
(117S) lowers the forks. Then check the 

DRIVE 

position according to item 3.1 and 

3.2  to  be  sure  the  Nut  (104S)  and Screw (318S) are in the proper position. 

 
3.4 

If the forks do not elevate while pumping in the 

RAISE 

position, turn the Nut (104S) 

or Screw (318S) counter-clockwise until the forks elevate while pumping in the 

RAISE 

position. Then check the 

LOWER 

and 

DRIVE 

position according to item 3.1, 3.2 

and item 3.3. 

 

4. MAINTENANCE

 

 

 
The pallet truck is mostly maintenance-free. 

 

 

4.1 OIL

 

Please check the oil level every six months. The oil can be hydraulic oil: ISO VG32, its 
viscosity should be 30cSt at 104°F (40°C), total volume is about 0.4lt. 

 

 

4.2 AIR REMOVAL

 

Air may contaminate the hydraulic oil through use during transportation or pumping up to a 
position. It can cause the forks to not elevate while pumping in the 

RAISE 

position. The air 

can been cleared out by setting the control handle (117S) to the 

LOWER 

position, then 

moving the draw-bar up and down repeatedly. 

 

4.3 DAILY CHECK AND MAINTENANCE

 

Check the pallet truck daily to limit wear as much as possible. Pay special attention to the 
wheels and the axles because thread, rags, etc. may block the wheels. The forks should be 
unloaded and set to the lowest position when not in use.   

 

4.4 LUBRICATION

 

All bearings and shafts are provided with long-life grease at the factory. Long-life  grease 
only needs to be applied at monthly intervals or after each thorough cleaning of the 
lubrication points. 

 

 
 
 
 
 
 
 

Stainless Steel Pallet Truck 

(Part # 272152)  

Instruction Manual 

 

ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO PALLET 

TRUCK, READ THESE INSTRUCTIONS ENTIRELY BEFORE USING. 

Industrial Products, Inc. 

Summary of Contents for 272152















Reviews: