Wenglor UMF303U035 Operating Instructions Manual Download Page 22

Page: 22 / 23

IO-Link

10. IO-Link

Process and parameter data can be found in the interface protocol under:
www.wenglor.com



Product World



Search (Enter the product number)



Download



Interface protocol

Process bytes
Output status is the status of the switching and error output.
The result is the distance value in 1/10 mm.

11. Maintenance Instructions

• This wenglor sensor is maintenance-free.
• It is advisable to clean the sensing face and the display, and to check the plug connections

at regular intervals.

• Do not clean with solvents or cleansers which could damage the device.

12. Proper Disposal

wenglor sensoric GmbH does not accept the return of unusable or irreparable products. Respectively valid
national waste disposal regulations apply to product disposal.

13. Appendix

13.1 Change Index, Operating Instructions

Version

Date

Description/Change

1.0.0

14.05.13

Initial version of the operating instructions

1.1.0

08.04.19

Further Information on Installation (blind spot)

Summary of Contents for UMF303U035
























Search results

Summary of Contents for UMF303U035

Reviews:

Related manuals for UMF303U035

Brands by name

Popular brands

Wenglor UMF303U035, Operating Instructions Manual

Search results

Summary of Contents for UMF303U035

Reviews:

Related manuals for UMF303U035

Brands by name

Popular brands