Wenger Corner Cabinet Assembly Instructions Manual Download Page 10

Page: 10 / 52

18. Turn the Right Hand Side Panel (15) over so that the outside surface is facing down (dowel holes

will now be visible).

19. Using a mallet, drive three Wood Dowels (4) into the three

” diameter pilot holes close to the top

edge of the Right Hand Side Panel (15).

NOTE:

The dowel holes do not go all the way through and are on the inside surface of the Side Panel.

20. Using the mallet, drive two Tack Glides (3) into the bottom surface of the Right Hand Side Panel

(15) about 1

” from each bottom corner as shown below.

NOTE:

Depending on Corner Cabinet configuration, hole positioning in the individual panels may vary.

Right Hand Side Panel (15) with

inside surface facing up

Wood Dowel (4)

Top Edge

Wood Dowel (4)

" Clearance Hole

" Deep

" Pilot Hole through

Inside Surface

Bottom Edge

Drive Glide into bottom surface

about 1” to 1

" from corner

edge

Tack Glide (3)

ORNER

ABINET

SSEMBLY

ONTINUED

Summary of Contents for Corner Cabinet





















































Search results

Summary of Contents for Corner Cabinet

Reviews:

Related manuals for Corner Cabinet

Brands by name

Popular brands

Wenger Corner Cabinet, Assembly Instructions Manual

Search results

Summary of Contents for Corner Cabinet

Reviews:

Related manuals for Corner Cabinet

Brands by name

Popular brands