Wen CT1065 Instruction Manual Download Page 23

Page: 23 / 28

TROUBLESHOOTING GUIDE

PROBLEM

CAUSE

SOLUTION

Excessive noise

or vibration

Blade is installed improperly

Ensure blade is installed in correct orientation.

Blade is damaged

Replace blade.

Blade is not secure

Make sure the blade flanges are flush against the blade and
arbor bolt is tightened completely.

Cutting too fast

Do not force the tool. Let it work at its own pace. Ensure blade
selection is appropriate for cut type and workpiece.

Worn bearings

Stop using the tool and call 1-800-232-1195 for customer
service.

Blade will not

turn

Spindle lock engaged

Disengage the spindle lock; move blade back and forth to
ensure it is disengaged.

Worn bearings

Stop using the tool and call 1-800-232-1195 for customer
service.

Defective gears

Stop using the tool and call 1-800-232-1195 for customer
service.

Saw will not

plunge

Plunge button not pressed, or not
pressed all the way

Ensure plunge button is fully pressed before beginning plunge.

Incorrect plunge mode selected

Select correct plunge mode (see page 13).

Broken plunge linkage

Stop using the tool and call 1-800-232-1195 for customer
service.

WARNING:

Stop using the tool immediately if any of the following problems occur. Repairs and replace-

ments should only be performed by an authorized technician. For any questions, please contact our customer

service at (800) 232-1195, M-F 8-5 CST or email us at

[email protected]

MAINTENANCE

WARNING:

To avoid accidents, turn OFF and

unplug the tool from the electrical outlet before

cleaning, adjusting, or performing any maintenance

work.

WARNING:

Any attempt to repair or replace

electrical parts on this tool may be hazardous. Ser-

vicing of the tool must be performed by a qualified

technician. When servicing, use only identical WEN

replacement parts. Use of other parts may be haz-

ardous or induce product failure.

ROUTINE INSPECTION

Before each use, inspect the general condition of the

tool. If any of these following conditions exist, do not

use until parts are replaced or the saw is properly re-

paired.

Check for:

• Loose hardware,

• Misalignment or binding of moving parts,

• Damaged cord/electrical wiring,

• Cracked or broken parts, and

• Any other condition that may affect its safe operation

Maintenance information continues on the next page.

Summary of Contents for CT1065





























Search results

Summary of Contents for CT1065

Reviews:

Related manuals for CT1065

Brands by name

Popular brands

Wen CT1065, Instruction Manual

Search results

Summary of Contents for CT1065

Reviews:

Related manuals for CT1065

Brands by name

Popular brands