background image

WaRNING:

 Every time the attachment is changed, ensure that the attachment receiver has no signs 

of severe wear or heavy impacts. After every tool change, pull on the tool to check that it is firmly 
seated inside the receiver.

aSSEMblING THE SCRaPER 

required tool: Open end wrench, 17 mm (not included).

Mount the scraper blade onto the holder using the two screws, washers 
and nuts (Fig. 1). Fully tighten the nuts using the 17 mm wrench.

lUbRICaTING THE aTTaCHMENT RECEIVER

Lubricate the attachment receiver (Fig. 2 - 1) before first use. Before each 
subsequent use, check that the receiver is lubricated. Failure to lubricate 
the receiver may shorten the lifespan of the tool. 

Hold the tool upside down with the attachment receiver facing upward. 
Put several drops of resin-free 30W non-detergent air tool oil into the at-
tachment receiver. NOTE: if oil emerges or if it runs down along the tool 
attachment, too much oil was used. 

INSERTING/REMOVING aTTaCHMENTS

1. Make sure the tool is disconnected from the air supply.

2. Hold the tool upside down with the attachment receiver (Fig. 2 - 1) 
pointing upwards. Support the other end on the ground. Make sure the 
attachment receiver is lightly lubricated. 

3. insert the selected tool into the attachment receiver. 

4. Slide the locking sleeve (Fig. 2 - 2) downwards until the tool slides into 
the receiver. Guide the locking sleeve up to lock the tool in position. 

5. Pull the tool to check that it has been correctly latched into the attach-
ment receiver. There should be some play, but the tool should NOT 
come out of the receiver.

To remove the attachment, make sure the tool has been disconnected 
from the air supply. Slide the locking sleeve (Fig. 2 - 2) halfway down-
wards and pull the attachment out. Guide the locking sleeve back into 
place.

MOuNTiNG ATTACHMENTS

WaRNING:

 To prevent injury from accidental startups, the tool must be diSCONNECTEd from 

the air supply before attaching or replacing accessories, or making any adjustments to the tool.

WaRNING:

 When handling sharp, pointed or hot attachments, always wear suitable protective 

gloves to avoid injuries. 

NOTE:

 Only use attachments that are designed for this tool. replacement tools can be purchased from wen-

products.com by searching their part number, outlined on the previous page.

1

2

Fig. 1 

Fig. 2 

9

Summary of Contents for 61635

















Reviews: