background image

 

 

50 

8-1 Create SIP Trunk 

 

Figure 8-1 SIP Trunk page 

 

 

 

Trunk ID: 

SIP trunk ID 1-4 

 

Register Type:

 Whether this account need register or not 

 

Register:

  When  it  is  set  to  register,  Welltech  2540  will  send 

REGISTER message to SIP proxy server for registration. 

 

Predefine:

 When it is set to predefine, Welltech 2540 will NOT 

send REGISTER message out. 

 

Domain: 

The SIP domain for register or call making 

 

Proxy Server:

 SIP registrar server address 

 

Proxy Server Port:

 SIP registrar server port number 

 

Outbound Proxy Server: 

outbound proxy server address 

 

Outbound Proxy server port:

 outbound proxy server port number 

 

Register Expires:

 the default register expires for negotiation 

 

TEL No:

 The registrar telephone number   

 

User ID:

 The SIP user ID for register and call making 

 

User Password:

 The SIP password for register and call making 

 

Display Name:

 The SIP display name 

 

Reject Anonymous Call: 

Reject the anonymous call   

 

Outgoing Caller ID:

 The outgoing SIP caller ID mode. 

-

Display Name:

 The display name will be set according to the 

Summary of Contents for 2540 FXO
















































































Reviews: