background image

 

DO  NOT  attempt  to  fix  the  unit  by  disassembling  or 
modification. You  can  cause  self  injury  and  disassembling 
and modifying the unit will void your warranty. 

 

Ensure that the cable does not jam or comes into contact with 
hot surfaces or sharp edges. 

 

Connection to the mains supply must be in accordance with 
the national regulations for electrical installations. 

 
WARNING: Explosion and Fire Hazard 
 

 

RISK OF EXPLOSIVE GASES.

 

 

a) WORKING IN VICINITY OF ALEAD-ACID BATTERY IS 
DANGEROUS.  BATTERIES  GENERATE  EXPLOSIVE 
GASES DURING NORMAL BATTERY OPERATION. 
FOR  THIS  REASON,  IT  IS  OF  UTMOST  IMPORTANCE 
THAT  YOU  FOLLOW  THE  INSTRUCTIONS  EACH  TIME 
YOU USE THE CHARGER. 

 

b) To reduce risk of battery explosion, follow these instructions 
and those published by battery manufacturer and manufacturer of 
any equipment you intend to use in vicinity of battery. Review 
cautionary marking on these products and on engine. 

 

Never charge a frozen battery. 

 

Never charge a damaged battery. 

 

Never  allow  red  and  black  clamps  to  touch  each  other  or 
another common metal conductor. This could create a spark. 

 

Make  sure  the  area  around  the  battery  and  charger  is  well 
ventilated. DO NOT use this product in an enclosed space. 
The internal battery may vent explosive hydrogen gas, which 
can be ignited by sparks from electrical connections. 

 

DO NOT use this product where there are flammable fumes 
or gases, such as in the bilge of a gasoline-powered boat, or 
near propane tanks. 

 

Never  smoke  or  allow  a  spark  or  flame  in  vicinity  of  the 
engine or batteries. 

 

Be careful not to drop a metal object on the battery or allow 
a  metal  tool  to  simultaneously  touch  the  positive  and 
negative  cable  ends or  battery terminals.  It might spark or 
short-circuit the battery and cause an explosion. 

 

If  you  need  to  remove  the  clip  from  the  battery  terminal, 
ALWAYS remove the clip from the positive terminal from 
the  battery  first.  Make  sure  all  accessories  are  off  so  you 
don't cause an arc. 

 

The  battery  terminals  exposed  at  the  clamps  have  enough 
energy  present  to  cause  a  spark,  creating  an  explosion 

Summary of Contents for CHAR-CAR-8612-WL












Reviews: