background image

Welch-Ilmvac

5621 W. Howard Street

Niles, IL 60714

Phone: (847) 676-8800 (Technical Support)

Fax: (847) 677-8606

E-Mail: [email protected]

Web-Page: www.welchvacuum.com

Copyright© 1997-2007 Gardner Denver Welch Vacuum Technology, Inc.

Welch is registered trademarks of Gardner Denver

Warranty

 
 

This Welch Vacuum product is warranted to be free from defects in material and workmanship. 
This liability of Welch-Ilmvac under this warranty is limited to servicing, adjusting, repairing, 
or replacing any unit or component part which in the judgment of Welch-Ilmvac has not been 
misused, abused, or altered in any way or damaged by ingestion of foreign material causing 
impaired performance or rendering it inoperative. No other warranties are expressed or 
implied. The method of executing this warranty: servicing, adjusting, repairing, or replacing, 
shall be at the discretion of Welch-Ilmvac. Vacuum pumps that have been operated within a 
vacuum system, or other system, for any period, however short, will be repaired under this 
warranty rather than replaced.

 

The warranty is effective for one year from the date of original purchase when:

 

1. The warranty card has been completed and returned.

 

2. The product is returned to the factory or other designated service centers, freight prepaid.

 

3. The product in our judgment is defective through no action or fault of the user. 

 

If the product has become defective through misuse, abuse, alteration, or ingestion of foreign 
material, repairs will be billed regardless of the age of the product. In this event, an estimate of 
the repair costs will be submitted and authorization of these charges will be required before the 
product is repaired and returned.

Summary of Contents for 2562C-02















Reviews: