Welch Allyn SCANTEAM 3700 Wedge Technical Manual Download Page 75

Page: 75 / 100

11–3

SCANTEAM 3700 Wedge Technical Manual

To Reset Factory Settings

If you aren't sure

what

programming options have been set up in your

3700 Wedge, or you've changed some options and now want the factory

settings restored, see Section 7, Factory Settings and scan the

Factory

Default Settings

bar code.

If All Else Fails...

If you are still experiencing problems, call your

Distributor or Hand Held Products:

315-685-2476

(8 a.m. to 6 p.m. EST)

Fax: 315-685-4960

Web Site: www.handheld.com

E-Mail: [email protected]

(For more information on Customer Support

or Warranty information see the two sections

following this one.)

Summary of Contents for SCANTEAM 3700 Wedge





































































































Search results

Summary of Contents for SCANTEAM 3700 Wedge

Reviews:

Related manuals for SCANTEAM 3700 Wedge

Brands by name

Popular brands

Welch Allyn SCANTEAM 3700 Wedge, Technical Manual

Search results

Summary of Contents for SCANTEAM 3700 Wedge

Reviews:

Related manuals for SCANTEAM 3700 Wedge

Brands by name

Popular brands